aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
authorDongming Han <handongming@gl-inet.com>2020-07-22 15:12:17 +0800
committerPetr Štetiar <ynezz@true.cz>2020-12-25 10:38:13 +0100
commitb9389186b012e5bd99ea6523b8220aaee6ca0085 (patch)
treedbd3f2cbff4b01a787e1f55cc7bbddd7c3ae83dd /target/linux
parent3bb16185737c011b74e3166cf436785604b5f47f (diff)
downloadupstream-b9389186b012e5bd99ea6523b8220aaee6ca0085.tar.gz
upstream-b9389186b012e5bd99ea6523b8220aaee6ca0085.tar.bz2
upstream-b9389186b012e5bd99ea6523b8220aaee6ca0085.zip
ipq40xx: add support for GL.iNet GL-AP1300
Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: Reset LED: Power, Internet UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 OTHER: On board with BLE module - by cp210x USB serial chip On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi (IPQ40xx) # run lf By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
Diffstat (limited to 'target/linux')
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata2
-rw-r--r--target/linux/ipq40xx/base-files/lib/upgrade/platform.sh1
-rw-r--r--target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-gl-ap1300.dts269
-rw-r--r--target/linux/ipq40xx/image/Makefile15
-rw-r--r--target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch3
6 files changed, 290 insertions, 1 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 07bacaf51b..fe21dc8035 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -92,6 +92,7 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan"
;;
+ glinet,gl-ap1300 |\
glinet,gl-b1300 |\
glinet,gl-s1300)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 7293438dfa..c4d9dd78e3 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -55,6 +55,7 @@ case "$FIRMWARE" in
alfa-network,ap120c-ac |\
cilab,meshpoint-one |\
ezviz,cs-w3-wd1200g-eup |\
+ glinet,gl-ap1300 |\
glinet,gl-b1300 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\
@@ -158,6 +159,7 @@ case "$FIRMWARE" in
alfa-network,ap120c-ac |\
cilab,meshpoint-one |\
ezviz,cs-w3-wd1200g-eup |\
+ glinet,gl-ap1300 |\
glinet,gl-b1300 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index e43225cbb2..5582696759 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -69,6 +69,7 @@ platform_do_upgrade() {
edgecore,ecw5211 |\
edgecore,oap100 |\
engenius,eap2200 |\
+ glinet,gl-ap1300 |\
luma,wrtq-329acn |\
mobipromo,cm520-79f |\
qxwlan,e2600ac-c2)
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-gl-ap1300.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-gl-ap1300.dts
new file mode 100644
index 0000000000..3fd5406d39
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-gl-ap1300.dts
@@ -0,0 +1,269 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "GL.iNet GL-AP1300";
+ compatible = "glinet,gl-ap1300";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1 clk_ignore_unused";
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ switch_lan_bmp = <0x18>;
+ switch_wan_bmp = <0x20>;
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "green:power";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ wan {
+ label = "green:wan";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ status = "okay";
+
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 5 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ status = "okay";
+
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "APPSBLENV"; /* uboot env*/
+ reg = <0x000e0000 0x00010000>;
+ };
+
+ partition@f0000 {
+ label = "APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition@170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ };
+ };
+
+ spi-nand@1 {
+ status = "okay";
+
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ubi";
+ reg = <0x00000000 0x08000000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi0_pins: spi0_pinmux {
+ mux_spi {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio5";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "GL-AP1300";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "GL-AP1300";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 487f3b5638..c19dcb4039 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -482,6 +482,21 @@ define Device/ezviz_cs-w3-wd1200g-eup
endef
TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
+define Device/glinet_gl-ap1300
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := GL.iNet
+ DEVICE_MODEL := GL-AP1300
+ SOC := qcom-ipq4018
+ DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 131072k
+ KERNEL_INSTALL := 1
+ DEVICE_PACKAGES := ipq-wifi-glinet_gl-ap1300
+endef
+TARGET_DEVICES += glinet_gl-ap1300
+
define Device/glinet_gl-b1300
$(call Device/FitImage)
DEVICE_VENDOR := GL.iNet
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index d470bb7204..a3d3341587 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,57 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,58 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -28,6 +28,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4018-ex6100v2.dtb \
+ qcom-ipq4018-ex6150v2.dtb \
+ qcom-ipq4018-fritzbox-4040.dtb \
++ qcom-ipq4018-gl-ap1300.dtb \
+ qcom-ipq4018-jalapeno.dtb \
+ qcom-ipq4018-meshpoint-one.dtb \
+ qcom-ipq4018-nbg6617.dtb \