aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
authorDavide Fioravanti <pantanastyle@gmail.com>2019-05-05 22:35:00 +0200
committerChristian Lamparter <chunkeey@gmail.com>2019-05-18 17:59:49 +0200
commitf5d2c91415a68f554815860d574145644fc31c16 (patch)
treee526274ac8f848615500c6d011c5bdb8be7c3cd1 /target/linux
parentc349cc5752165c65d4133374755f07fc30004e74 (diff)
downloadupstream-f5d2c91415a68f554815860d574145644fc31c16.tar.gz
upstream-f5d2c91415a68f554815860d574145644fc31c16.tar.bz2
upstream-f5d2c91415a68f554815860d574145644fc31c16.zip
ath79: add support for TP-Link Archer D50 V1
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem. The router section is based on Qualcomm/Atheros QCA9531 + QCA9882. The "DSL" section is based on BCM6318 but it's currently not supported. Internally eth0 is connected to the Broadcom CPU. Router section - Specification: CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB) RAM: 64 MB (DDR2) Flash: 8 MB (SPI NOR) Wifi 2.4GHz: QCA9531 2T2R Wifi 5GHz: QCA9982 2T2R 4x 10/100 Mbps Ethernet 8x LED, 3x button UART header on PCB Known issues: DSL not working (eth0) (WIP) UART connection --------------- J2 HEADER (Qualcomm CPU) . TX . RX . GND O VCC J16 HEADER (Broadcom CPU) O VCC . GND . RX . TX The following instructions require a connection to the J2 UART header. Flash instruction under U-Boot, using UART ------------------------------------------ 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Initramfs instruction under U-Boot for testing, using UART ---------------------------------------------------------- 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin bootm 0x81000000 Restore the original firmware ----------------------------- 0. Backup every partition using the OpenWrt web interface 1. Download the OEM firmware from the TP-Link website 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin) 3. Remove the U-Boot and the Broadcom image part from the file. Issue the following command: dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616 4. Double check the .mod file size. It must be 7995392 bytes. 5. Flash it using the OpenWrt web interface. Force the update if needed. WARNING: Remember to NOT keep settings. 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection. Issue below commands in the U-Boot: tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed default-state = "off", it's already the default, added pcie node, fixed typo]
Diffstat (limited to 'target/linux')
-rwxr-xr-xtarget/linux/ath79/base-files/etc/board.d/01_leds5
-rwxr-xr-xtarget/linux/ath79/base-files/etc/board.d/02_network4
-rw-r--r--target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata4
-rw-r--r--target/linux/ath79/dts/qca9531_tplink_archer-d50-v1.dts185
-rw-r--r--target/linux/ath79/image/generic-tp-link.mk21
5 files changed, 219 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds
index 9bcfbb2b0a..69e26a4773 100755
--- a/target/linux/ath79/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -136,6 +136,11 @@ tplink,cpe210-v3)
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "tp-link:green:link3" "wlan0" "60" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "tp-link:green:link4" "wlan0" "80" "100"
;;
+tplink,archer-d50-v1)
+ ucidef_set_led_switch "lan" "LAN" "tp-link:white:lan" "switch0" "0x1E"
+ ucidef_set_led_netdev "wan_data" "WAN Data" "tp-link:white:internet" "eth1.2" "tx rx"
+ ucidef_set_led_netdev "wan_link" "WAN Link" "tp-link:white:wan" "eth1.2" "link"
+ ;;
tplink,re450-v2)
ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 897b59af33..7b89274ccf 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -178,6 +178,10 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
;;
+ tplink,archer-d50-v1)
+ ucidef_add_switch "switch0" \
+ "0@eth1" "2:lan:3" "3:lan:2" "4:lan:1" "1:wan"
+ ;;
buffalo,whr-g301n|\
tplink,tl-mr3220-v1|\
tplink,tl-mr3420-v1|\
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 47c72ce372..b2f5d17213 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -147,6 +147,10 @@ case "$FIRMWARE" in
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
;;
+ tplink,archer-d50-v1)
+ ath10kcal_extract "art" 20480 2116
+ ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) +2)
+ ;;
tplink,re350k-v1)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +2)
diff --git a/target/linux/ath79/dts/qca9531_tplink_archer-d50-v1.dts b/target/linux/ath79/dts/qca9531_tplink_archer-d50-v1.dts
new file mode 100644
index 0000000000..25c1d050da
--- /dev/null
+++ b/target/linux/ath79/dts/qca9531_tplink_archer-d50-v1.dts
@@ -0,0 +1,185 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca953x.dtsi"
+
+/ {
+ compatible = "tplink,archer-d50-v1", "qca,qca9531";
+ model = "TP-Link Archer D50 v1";
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ gpio_leds: leds {
+ compatible = "gpio-leds";
+
+ led_wlan2g: wlan2g {
+ label = "tp-link:white:wlan2g";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led_wlan5g: wlan5g {
+ label = "tp-link:white:wlan5g";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ qss_led: qss {
+ label = "tp-link:white:qss";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ wan {
+ label = "tp-link:white:wan";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ lan {
+ label = "tp-link:white:lan";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ usb {
+ label = "tp-link:white:usb";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&hub_port0>;
+ linux,default-trigger = "usbport";
+ };
+
+ internet {
+ label = "tp-link:white:internet";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ system: system{
+ label = "tp-link:white:system";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ rfkill {
+ label = "RFKILL button";
+ linux,code = <KEY_RFKILL>;
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "WPS button";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ partition@20000 {
+ compatible = "tplink,firmware";
+ label = "firmware";
+ reg = <0x020000 0x7a0000>;
+ };
+
+ partition@7c0000 {
+ label = "config";
+ reg = <0x7c0000 0x010000>;
+ read-only;
+ };
+
+ romfile: partition@7d0000 {
+ label = "romfile";
+ reg = <0x7d0000 0x010000>;
+ read-only;
+ };
+
+ partition@7e0000 {
+ label = "rom";
+ reg = <0x7e0000 0x010000>;
+ read-only;
+ };
+
+ art: partition@7f0000 {
+ label = "art";
+ reg = <0x7f0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&eth1 {
+ mtd-mac-address = <&romfile 0xf100>;
+};
+
+&eth0 {
+ status = "okay";
+ phy-handle = <&swphy4>;
+
+ mtd-mac-address = <&romfile 0xf100>;
+ mtd-mac-address-increment = <1>;
+};
+
+&wmac {
+ status = "okay";
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&romfile 0xf100>;
+};
+
+&pcie0 {
+ status = "okay";
+
+ wifi@0,0 {
+ compatible = "pci168c,003c";
+ reg = <0x0000 0 0 0 0>;
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&usb0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ hub_port0: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index a3e1708fe1..4a5bb93864 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -133,6 +133,27 @@ define Device/tplink_cpe210-v3
endef
TARGET_DEVICES += tplink_cpe210-v3
+define Device/tplink_archer-d50-v1
+ ATH_SOC := qca9531
+ DEVICE_TITLE := TP-Link Archer D50 v1
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k-ct ath10k-firmware-qca988x-ct
+ BOARDNAME := ARCHER-D50-V1
+ IMAGE_SIZE := 7808k
+ TPLINK_HWID := 0xC1200001
+ TPLINK_HWREV := 0x00000046
+ TPLINK_FLASHLAYOUT := 8Mqca
+ TPLINK_HWREVADD := 0x00000000
+ TPLINK_HVERSION := 3
+ KERNEL := kernel-bin | append-dtb | lzma
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | \
+ tplink-v2-header -s -V "ver. 1.0"
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := tplink-v2-image -s -V "ver. 2.0" | \
+ append-metadata | check-size $$$$(IMAGE_SIZE)
+ SUPPORTED_DEVICES += archer-d50-v1
+endef
+TARGET_DEVICES += tplink_archer-d50-v1
+
define Device/tplink_re350k-v1
$(Device/tplink-safeloader)
ATH_SOC := qca9558