diff options
Diffstat (limited to 'package/boot/uboot-mvebu/patches/132-arm64-dts-armada-3720-espressobin-split-common-parts.patch')
| -rw-r--r-- | package/boot/uboot-mvebu/patches/132-arm64-dts-armada-3720-espressobin-split-common-parts.patch | 369 |
1 files changed, 369 insertions, 0 deletions
diff --git a/package/boot/uboot-mvebu/patches/132-arm64-dts-armada-3720-espressobin-split-common-parts.patch b/package/boot/uboot-mvebu/patches/132-arm64-dts-armada-3720-espressobin-split-common-parts.patch new file mode 100644 index 0000000000..d3af221c01 --- /dev/null +++ b/package/boot/uboot-mvebu/patches/132-arm64-dts-armada-3720-espressobin-split-common-parts.patch @@ -0,0 +1,369 @@ +From ee59573dd531df96de0d9dc8e79b34ed3716c864 Mon Sep 17 00:00:00 2001 +From: Andre Heider <a.heider@gmail.com> +Date: Fri, 4 Sep 2020 15:38:58 +0200 +Subject: [PATCH] arm64: dts: armada-3720-espressobin: split common parts to + .dtsi + +Move most of the dts to the new common +arch/arm/dts/armada-3720-espressobin.dtsi file, just like Linux has. + +The dts itself is imported from Linux. + +Signed-off-by: Andre Heider <a.heider@gmail.com> +--- + arch/arm/dts/armada-3720-espressobin.dts | 190 ++---------------- + ...sobin.dts => armada-3720-espressobin.dtsi} | 3 - + 2 files changed, 20 insertions(+), 173 deletions(-) + rewrite arch/arm/dts/armada-3720-espressobin.dts (95%) + copy arch/arm/dts/{armada-3720-espressobin.dts => armada-3720-espressobin.dtsi} (96%) + +--- a/arch/arm/dts/armada-3720-espressobin.dts ++++ b/arch/arm/dts/armada-3720-espressobin.dts +@@ -1,170 +1,20 @@ ++// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + /* +- * Device Tree file for Marvell Armada 3720 community board +- * (ESPRESSOBin) ++ * Device Tree file for Globalscale Marvell ESPRESSOBin Board + * Copyright (C) 2016 Marvell + * +- * Gregory CLEMENT <gregory.clement@free-electrons.com> +- * Konstantin Porotchkin <kostap@marvell.com> ++ * Romain Perier <romain.perier@free-electrons.com> + * +- * This file is dual-licensed: you can use it either under the terms +- * of the GPL or the X11 license, at your option. Note that this dual +- * licensing only applies to this file, and not this project as a +- * whole. +- * +- * a) This file is free software; you can redistribute it and/or +- * modify it under the terms of the GNU General Public License as +- * published by the Free Software Foundation; either version 2 of the +- * License, or (at your option) any later version. +- * +- * This file is distributed in the hope that it will be useful +- * but WITHOUT ANY WARRANTY; without even the implied warranty of +- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +- * GNU General Public License for more details. +- * +- * Or, alternatively +- * +- * b) Permission is hereby granted, free of charge, to any person +- * obtaining a copy of this software and associated documentation +- * files (the "Software"), to deal in the Software without +- * restriction, including without limitation the rights to use +- * copy, modify, merge, publish, distribute, sublicense, and/or +- * sell copies of the Software, and to permit persons to whom the +- * Software is furnished to do so, subject to the following +- * conditions: +- * +- * The above copyright notice and this permission notice shall be +- * included in all copies or substantial portions of the Software. +- * +- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND +- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES +- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT +- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY +- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING +- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR +- * OTHER DEALINGS IN THE SOFTWARE. ++ */ ++/* ++ * Schematic available at http://espressobin.net/wp-content/uploads/2017/08/ESPRESSObin_V5_Schematics.pdf + */ + + /dts-v1/; + +-#include "armada-372x.dtsi" ++#include "armada-3720-espressobin.dtsi" + + / { + model = "Globalscale Marvell ESPRESSOBin Board"; + compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710"; +- +- chosen { +- stdout-path = "serial0:115200n8"; +- }; +- +- aliases { +- ethernet0 = ð0; +- i2c0 = &i2c0; +- spi0 = &spi0; +- }; +- +- memory { +- device_type = "memory"; +- reg = <0x00000000 0x00000000 0x00000000 0x20000000>; +- }; +- +- vcc_sd_reg0: regulator@0 { +- compatible = "regulator-gpio"; +- regulator-name = "vcc_sd0"; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <3300000>; +- regulator-type = "voltage"; +- states = <1800000 0x1 +- 3300000 0x0>; +- gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>; +- }; +-}; +- +-&comphy { +- max-lanes = <3>; +- phy0 { +- phy-type = <PHY_TYPE_USB3_HOST0>; +- phy-speed = <PHY_SPEED_5G>; +- }; +- +- phy1 { +- phy-type = <PHY_TYPE_PEX0>; +- phy-speed = <PHY_SPEED_2_5G>; +- }; +- +- phy2 { +- phy-type = <PHY_TYPE_SATA0>; +- phy-speed = <PHY_SPEED_5G>; +- }; +-}; +- +-ð0 { +- status = "okay"; +- pinctrl-names = "default"; +- pinctrl-0 = <&rgmii_pins>, <&smi_pins>; +- phy-mode = "rgmii"; +- phy_addr = <0x1>; +- fixed-link { +- speed = <1000>; +- full-duplex; +- }; +-}; +- +-&i2c0 { +- pinctrl-names = "default"; +- pinctrl-0 = <&i2c1_pins>; +- status = "okay"; +-}; +- +-/* CON3 */ +-&sata { +- status = "okay"; +-}; +- +-&sdhci0 { +- pinctrl-names = "default"; +- pinctrl-0 = <&sdio_pins>; +- bus-width = <4>; +- cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>; +- vqmmc-supply = <&vcc_sd_reg0>; +- status = "okay"; +-}; +- +-&spi0 { +- status = "okay"; +- pinctrl-names = "default"; +- pinctrl-0 = <&spi_quad_pins>; +- +- spi-flash@0 { +- #address-cells = <1>; +- #size-cells = <1>; +- compatible = "st,m25p128", "jedec,spi-nor"; +- reg = <0>; /* Chip select 0 */ +- spi-max-frequency = <50000000>; +- m25p,fast-read; +- }; +-}; +- +-/* Exported on the micro USB connector CON32 through an FTDI */ +-&uart0 { +- pinctrl-names = "default"; +- pinctrl-0 = <&uart1_pins>; +- status = "okay"; +-}; +- +-/* CON29 */ +-&usb2 { +- status = "okay"; +-}; +- +-/* CON31 */ +-&usb3 { +- status = "okay"; +-}; +- +-&pcie0 { +- pinctrl-names = "default"; +- pinctrl-0 = <&pcie_pins>; +- reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>; +- status = "okay"; + }; +--- /dev/null ++++ b/arch/arm/dts/armada-3720-espressobin.dtsi +@@ -0,0 +1,167 @@ ++/* ++ * Device Tree file for Marvell Armada 3720 community board ++ * (ESPRESSOBin) ++ * Copyright (C) 2016 Marvell ++ * ++ * Gregory CLEMENT <gregory.clement@free-electrons.com> ++ * Konstantin Porotchkin <kostap@marvell.com> ++ * ++ * This file is dual-licensed: you can use it either under the terms ++ * of the GPL or the X11 license, at your option. Note that this dual ++ * licensing only applies to this file, and not this project as a ++ * whole. ++ * ++ * a) This file is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of the ++ * License, or (at your option) any later version. ++ * ++ * This file is distributed in the hope that it will be useful ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * Or, alternatively ++ * ++ * b) Permission is hereby granted, free of charge, to any person ++ * obtaining a copy of this software and associated documentation ++ * files (the "Software"), to deal in the Software without ++ * restriction, including without limitation the rights to use ++ * copy, modify, merge, publish, distribute, sublicense, and/or ++ * sell copies of the Software, and to permit persons to whom the ++ * Software is furnished to do so, subject to the following ++ * conditions: ++ * ++ * The above copyright notice and this permission notice shall be ++ * included in all copies or substantial portions of the Software. ++ * ++ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND ++ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES ++ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND ++ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT ++ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY ++ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING ++ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR ++ * OTHER DEALINGS IN THE SOFTWARE. ++ */ ++ ++/dts-v1/; ++ ++#include "armada-372x.dtsi" ++ ++/ { ++ chosen { ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ aliases { ++ ethernet0 = ð0; ++ i2c0 = &i2c0; ++ spi0 = &spi0; ++ }; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x00000000 0x00000000 0x20000000>; ++ }; ++ ++ vcc_sd_reg0: regulator@0 { ++ compatible = "regulator-gpio"; ++ regulator-name = "vcc_sd0"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <3300000>; ++ regulator-type = "voltage"; ++ states = <1800000 0x1 ++ 3300000 0x0>; ++ gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>; ++ }; ++}; ++ ++&comphy { ++ max-lanes = <3>; ++ phy0 { ++ phy-type = <PHY_TYPE_USB3_HOST0>; ++ phy-speed = <PHY_SPEED_5G>; ++ }; ++ ++ phy1 { ++ phy-type = <PHY_TYPE_PEX0>; ++ phy-speed = <PHY_SPEED_2_5G>; ++ }; ++ ++ phy2 { ++ phy-type = <PHY_TYPE_SATA0>; ++ phy-speed = <PHY_SPEED_5G>; ++ }; ++}; ++ ++ð0 { ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&rgmii_pins>, <&smi_pins>; ++ phy-mode = "rgmii"; ++ phy_addr = <0x1>; ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++}; ++ ++&i2c0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ status = "okay"; ++}; ++ ++/* CON3 */ ++&sata { ++ status = "okay"; ++}; ++ ++&sdhci0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ bus-width = <4>; ++ cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>; ++ vqmmc-supply = <&vcc_sd_reg0>; ++ status = "okay"; ++}; ++ ++&spi0 { ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi_quad_pins>; ++ ++ spi-flash@0 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "st,m25p128", "jedec,spi-nor"; ++ reg = <0>; /* Chip select 0 */ ++ spi-max-frequency = <50000000>; ++ m25p,fast-read; ++ }; ++}; ++ ++/* Exported on the micro USB connector CON32 through an FTDI */ ++&uart0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins>; ++ status = "okay"; ++}; ++ ++/* CON29 */ ++&usb2 { ++ status = "okay"; ++}; ++ ++/* CON31 */ ++&usb3 { ++ status = "okay"; ++}; ++ ++&pcie0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pcie_pins>; ++ reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>; ++ status = "okay"; ++}; |