diff options
Diffstat (limited to 'target/linux/bcm27xx/patches-5.4/950-0321-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch')
| -rw-r--r-- | target/linux/bcm27xx/patches-5.4/950-0321-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch | 66 |
1 files changed, 66 insertions, 0 deletions
diff --git a/target/linux/bcm27xx/patches-5.4/950-0321-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch b/target/linux/bcm27xx/patches-5.4/950-0321-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch new file mode 100644 index 0000000000..6f487bf7c6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.4/950-0321-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch @@ -0,0 +1,66 @@ +From 5db0abcd74512cf7013c2ea87d347cd158726be3 Mon Sep 17 00:00:00 2001 +From: Markus Proeller <markus.proeller@pieye.org> +Date: Thu, 10 Oct 2019 19:12:08 +0200 +Subject: [PATCH] dt-bindings: Add binding for the Infineon IRS1125 + sensor + +Adds a binding for the Infineon IRS1125 time-of-flight depth +sensor. + +Signed-off-by: Markus Proeller <markus.proeller@pieye.org> +--- + .../devicetree/bindings/media/i2c/irs1125.txt | 48 +++++++++++++++++++ + 1 file changed, 48 insertions(+) + create mode 100644 Documentation/devicetree/bindings/media/i2c/irs1125.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/media/i2c/irs1125.txt +@@ -0,0 +1,48 @@ ++* Infineon irs1125 time of flight sensor ++ ++The Infineon irs1125 is a time of flight digital image sensor with ++an active array size of 352H x 286V. It is programmable through I2C ++interface. The I2C address defaults to 0x3D, but can be reconfigured ++to address 0x3C or 0x41 via I2C commands. Image data is sent through ++MIPI CSI-2, which is configured as either 1 or 2 data lanes. ++ ++Required Properties: ++- compatible: value should be "infineon,irs1125" for irs1125 sensor ++- reg: I2C bus address of the device ++- clocks: reference to the xclk input clock. ++- pwdn-gpios: reference to the GPIO connected to the reset pin. ++ This is an active low signal to the iirs1125. ++ ++The irs1125 device node should contain one 'port' child node with ++an 'endpoint' subnode. For further reading on port node refer to ++Documentation/devicetree/bindings/media/video-interfaces.txt. ++ ++Endpoint node required properties for CSI-2 connection are: ++- remote-endpoint: a phandle to the bus receiver's endpoint node. ++- clock-lanes: should be set to <0> (clock lane on hardware lane 0) ++- data-lanes: should be set to <1> or <1 2> (one or two lane CSI-2 ++ supported) ++ ++Example: ++ sensor@10 { ++ compatible = "infineon,irs1125"; ++ reg = <0x3D>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ clocks = <&irs1125_clk>; ++ pwdn-gpios = <&gpio 5 0>; ++ ++ irs1125_clk: camera-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <26000000>; ++ }; ++ ++ port { ++ sensor_out: endpoint { ++ remote-endpoint = <&csiss_in>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ }; ++ }; ++ }; |