diff options
Diffstat (limited to 'target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4029-ap-303h.dts')
-rw-r--r-- | target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4029-ap-303h.dts | 421 |
1 files changed, 0 insertions, 421 deletions
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4029-ap-303h.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4029-ap-303h.dts deleted file mode 100644 index 1f7a728492..0000000000 --- a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4029-ap-303h.dts +++ /dev/null @@ -1,421 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 OR MIT - -#include "qcom-ipq4019.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> -#include <dt-bindings/soc/qcom,tcsr.h> - -/ { - model = "Aruba AP-303H"; - compatible = "aruba,ap-303h"; - - aliases { - led-boot = &led_system_green; - led-failsafe = &led_system_red; - led-running = &led_system_green; - led-upgrade = &led_system_amber; - }; - - memory { - device_type = "memory"; - reg = <0x80000000 0x10000000>; - }; - - soc { - rng@22000 { - status = "okay"; - }; - - mdio@90000 { - status = "okay"; - pinctrl-0 = <&mdio_pins>; - pinctrl-names = "default"; - - reset-gpios = <&tlmm 19 GPIO_ACTIVE_LOW>; - reset-delay-us = <2000>; - }; - - counter@4a1000 { - compatible = "qcom,qca-gcnt"; - reg = <0x4a1000 0x4>; - }; - - ess_tcsr@1953000 { - compatible = "qcom,tcsr"; - reg = <0x1953000 0x1000>; - qcom,ess-interface-select = <TCSR_ESS_PSGMII>; - }; - - tcsr@1949000 { - compatible = "qcom,tcsr"; - reg = <0x1949000 0x100>; - qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; - }; - - tcsr@194b000 { - compatible = "qcom,tcsr"; - reg = <0x194b000 0x100>; - qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; - }; - - tcsr@1957000 { - compatible = "qcom,tcsr"; - reg = <0x1957000 0x100>; - qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; - }; - - usb2@60f8800 { - status = "okay"; - }; - - crypto@8e3a000 { - status = "okay"; - }; - - watchdog@b017000 { - status = "okay"; - }; - - ess-switch@c000000 { - status = "okay"; - }; - - edma@c080000 { - status = "okay"; - }; - - i2c_0: i2c@78b7000 { - pinctrl-0 = <&i2c_0_pins>; - pinctrl-names = "default"; - status = "okay"; - - tpm@29 { - /* No Driver */ - compatible = "atmel,at97sc3203"; - reg = <0x29>; - read-only; - }; - - power-monitor@40 { - /* No driver */ - compatible = "isl,isl28022"; - reg = <0x40>; - }; - }; - }; - - leds { - compatible = "gpio-leds"; - - wifi_green { - label = "ap-303h:green:wifi"; - gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "phy0tpt"; - }; - - wifi_amber { - label = "ap-303h:amber:wifi"; - gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "phy1tpt"; - }; - - pse { - label = "ap-303h:green:pse"; - gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; - }; - - led_system_red: system_red { - label = "ap-303h:red:system"; - gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>; - }; - - led_system_green: system_green { - label = "ap-303h:green:system"; - gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>; - }; - - led_system_amber: system_amber { - label = "ap-303h:amber:system"; - gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>; - }; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "Reset button"; - gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - }; - }; -}; - -&blsp_dma { - status = "okay"; -}; - -&blsp1_uart1 { - pinctrl-0 = <&serial_0_pins>; - pinctrl-names = "default"; - status = "okay"; -}; - -&blsp1_uart2 { - /* Texas Instruments CC2540T BLE radio */ - pinctrl-0 = <&serial_1_pins>; - pinctrl-names = "default"; - status = "okay"; -}; - -&cryptobam { - status = "okay"; -}; - -&qpic_bam { - status = "okay"; -}; - -&tlmm { - /* - * In addition to the Pins listed below, - * the following GPIOs have "features": - * 39 - out - active low to force HW reset - * 32 - out - active low to reset TPM - * 43 - out - active low to reset BLE radio - * 41 - out - pulse to set warm reset status - * 34 - out - active low to enable PSE port - * 22 - in - active low when 802.3at powered - * 29 - in - active high when DC powered - * 40 - in - active low when reset due to cold HW reset - * 30 - in - active low when USB overcurrent detected - * 35 - in - interrupt line for power monitor chip - * 31 - in - active low when PSE port active - */ - mdio_pins: mdio_pinmux { - mux_1 { - pins = "gpio6"; - function = "mdio"; - bias-pull-up; - }; - mux_2 { - pins = "gpio7"; - function = "mdc"; - bias-pull-up; - }; - }; - - spi_0_pins: spi_0_pinmux { - pin { - function = "blsp_spi0"; - pins = "gpio13", "gpio14", "gpio15"; - drive-strength = <12>; - bias-disable; - }; - pin_cs { - function = "gpio"; - pins = "gpio12", "gpio59"; - drive-strength = <2>; - bias-disable; - output-high; - }; - }; - - i2c_0_pins: i2c_0_pinmux { - mux { - pins = "gpio20", "gpio21"; - function = "blsp_i2c0"; - drive-strength = <4>; - bias-disable; - }; - }; - - serial_0_pins: serial_0_pinmux { - mux { - pins = "gpio16", "gpio17"; - function = "blsp_uart0"; - bias-disable; - }; - }; - - serial_1_pins: serial_1_pinmux { - mux { - pins = "gpio8", "gpio9"; - function = "blsp_uart1"; - bias-disable; - }; - }; - - usb-power { - line-name = "USB-power"; - gpios = <23 GPIO_ACTIVE_HIGH>; - gpio-hog; - output-high; - }; -}; - -&blsp1_spi1 { - pinctrl-0 = <&spi_0_pins>; - pinctrl-names = "default"; - status = "okay"; - cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <24000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - /* - * There is no partition map for the NOR flash - * in the stock firmware. - * - * All partitions here are based on offsets - * found in the U-Boot GPL code and information - * from smem. - */ - - partition@0 { - label = "sbl1"; - reg = <0x0 0x40000>; - read-only; - }; - - partition@40000 { - label = "mibib"; - reg = <0x40000 0x20000>; - read-only; - }; - - partition@60000 { - label = "qsee"; - reg = <0x60000 0x60000>; - read-only; - }; - - partition@c0000 { - label = "cdt"; - reg = <0xc0000 0x10000>; - read-only; - }; - - partition@d0000 { - label = "ddrparams"; - reg = <0xd0000 0x10000>; - read-only; - }; - - partition@e0000 { - label = "appsblenv"; - reg = <0xe0000 0x10000>; - read-only; - }; - - partition@f0000 { - label = "appsbl"; - reg = <0xf0000 0x100000>; - read-only; - }; - - partition@1e0000 { - label = "ART"; - reg = <0x1f0000 0x10000>; - read-only; - }; - - partition@1f0000 { - label = "osss"; - reg = <0x200000 0x170000>; - read-only; - }; - - partition@200000 { - label = "pds"; - reg = <0x370000 0x10000>; - read-only; - }; - - partition@380000 { - label = "apcd"; - reg = <0x380000 0x10000>; - read-only; - }; - - partition@390000 { - label = "mfginfo"; - reg = <0x390000 0x10000>; - read-only; - }; - - partition@3a0000 { - label = "fcache"; - reg = <0x3a0000 0x10000>; - read-only; - }; - - partition@3b0000 { - /* Called osss1 in smem */ - label = "u-boot-env-bak"; - reg = <0x3b0000 0x10000>; - read-only; - }; - - partition@3f0000 { - label = "u-boot-env"; - reg = <0x3c0000 0x40000>; - read-only; - }; - }; - }; - - flash@1 { - status = "okay"; - - compatible = "spi-nand"; - reg = <1>; - spi-max-frequency = <24000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - /* 'aos0' in Aruba firmware */ - label = "aos0"; - reg = <0x0 0x2000000>; - read-only; - }; - - partition@2000000 { - /* 'aos1' in Aruba firmware */ - label = "ubi"; - reg = <0x2000000 0x2000000>; - }; - - partition@4000000 { - label = "aruba-ubifs"; - reg = <0x4000000 0x4000000>; - read-only; - }; - }; - }; -}; - -&usb2_hs_phy { - status = "okay"; -}; - -&wifi0 { - status = "okay"; - qcom,ath10k-calibration-variant = "Aruba-AP-303"; -}; - -&wifi1 { - status = "okay"; - qcom,ath10k-calibration-variant = "Aruba-AP-303"; -}; |