diff options
Diffstat (limited to 'target/linux/ipq40xx/patches-4.19/712-mr33-essedma.patch')
| -rw-r--r-- | target/linux/ipq40xx/patches-4.19/712-mr33-essedma.patch | 334 |
1 files changed, 0 insertions, 334 deletions
diff --git a/target/linux/ipq40xx/patches-4.19/712-mr33-essedma.patch b/target/linux/ipq40xx/patches-4.19/712-mr33-essedma.patch deleted file mode 100644 index ee6452eebb..0000000000 --- a/target/linux/ipq40xx/patches-4.19/712-mr33-essedma.patch +++ /dev/null @@ -1,334 +0,0 @@ ---- a/drivers/net/ethernet/qualcomm/essedma/edma.c -+++ b/drivers/net/ethernet/qualcomm/essedma/edma.c -@@ -161,8 +161,10 @@ static void edma_configure_rx(struct edm - /* Set Rx FIFO threshold to start to DMA data to host */ - rxq_ctrl_data = EDMA_FIFO_THRESH_128_BYTE; - -+ if (!edma_cinfo->is_single_phy) { - /* Set RX remove vlan bit */ - rxq_ctrl_data |= EDMA_RXQ_CTRL_RMV_VLAN; -+ } - - edma_write_reg(EDMA_REG_RXQ_CTRL, rxq_ctrl_data); - } -@@ -1293,6 +1295,10 @@ void edma_adjust_link(struct net_device - if (status == __EDMA_LINKUP && adapter->link_state == __EDMA_LINKDOWN) { - dev_info(&adapter->pdev->dev, "%s: GMAC Link is up with phy_speed=%d\n", netdev->name, phydev->speed); - adapter->link_state = __EDMA_LINKUP; -+ if (adapter->edma_cinfo->is_single_phy) { -+ ess_set_port_status_speed(adapter->edma_cinfo, phydev, -+ ffs(adapter->dp_bitmap) - 1); -+ } - netif_carrier_on(netdev); - if (netif_running(netdev)) - netif_tx_wake_all_queues(netdev); -@@ -1386,10 +1392,12 @@ netdev_tx_t edma_xmit(struct sk_buff *sk - } - - /* Check and mark VLAN tag offload */ -- if (skb_vlan_tag_present(skb)) -- flags_transmit |= EDMA_VLAN_TX_TAG_INSERT_FLAG; -- else if (adapter->default_vlan_tag) -- flags_transmit |= EDMA_VLAN_TX_TAG_INSERT_DEFAULT_FLAG; -+ if (!adapter->edma_cinfo->is_single_phy) { -+ if (unlikely(skb_vlan_tag_present(skb))) -+ flags_transmit |= EDMA_VLAN_TX_TAG_INSERT_FLAG; -+ else if (adapter->default_vlan_tag) -+ flags_transmit |= EDMA_VLAN_TX_TAG_INSERT_DEFAULT_FLAG; -+ } - - /* Check and mark checksum offload */ - if (likely(skb->ip_summed == CHECKSUM_PARTIAL)) ---- a/drivers/net/ethernet/qualcomm/essedma/edma.h -+++ b/drivers/net/ethernet/qualcomm/essedma/edma.h -@@ -31,6 +31,7 @@ - #include <linux/platform_device.h> - #include <linux/of.h> - #include <linux/of_device.h> -+#include <linux/clk.h> - #include <linux/kernel.h> - #include <linux/device.h> - #include <linux/sysctl.h> -@@ -332,6 +333,9 @@ struct edma_common_info { - struct edma_per_cpu_queues_info edma_percpu_info[CONFIG_NR_CPUS]; /* per cpu information */ - spinlock_t stats_lock; /* protect edma stats area for updation */ - struct timer_list edma_stats_timer; -+ bool is_single_phy; -+ void __iomem *ess_hw_addr; -+ struct clk *ess_clk; - }; - - /* transimit packet descriptor (tpd) ring */ -@@ -444,4 +448,6 @@ void edma_change_tx_coalesce(int usecs); - void edma_change_rx_coalesce(int usecs); - void edma_get_tx_rx_coalesce(u32 *reg_val); - void edma_clear_irq_status(void); -+void ess_set_port_status_speed(struct edma_common_info *edma_cinfo, -+ struct phy_device *phydev, uint8_t port_id); - #endif /* _EDMA_H_ */ ---- a/drivers/net/ethernet/qualcomm/essedma/edma_axi.c -+++ b/drivers/net/ethernet/qualcomm/essedma/edma_axi.c -@@ -17,6 +17,11 @@ - #include <linux/of.h> - #include <linux/of_net.h> - #include <linux/timer.h> -+#include <linux/of_platform.h> -+#include <linux/of_address.h> -+#include <linux/clk.h> -+#include <linux/string.h> -+#include <linux/reset.h> - #include "edma.h" - #include "ess_edma.h" - -@@ -81,6 +86,101 @@ void edma_read_reg(u16 reg_addr, volatil - *reg_value = readl((void __iomem *)(edma_hw_addr + reg_addr)); - } - -+static void ess_write_reg(struct edma_common_info *edma, u16 reg_addr, u32 reg_value) -+{ -+ writel(reg_value, ((void __iomem *) -+ ((unsigned long)edma->ess_hw_addr + reg_addr))); -+} -+ -+static void ess_read_reg(struct edma_common_info *edma, u16 reg_addr, -+ volatile u32 *reg_value) -+{ -+ *reg_value = readl((void __iomem *) -+ ((unsigned long)edma->ess_hw_addr + reg_addr)); -+} -+ -+static int ess_reset(struct edma_common_info *edma) -+{ -+ struct device_node *switch_node = NULL; -+ struct reset_control *ess_rst; -+ u32 regval; -+ -+ switch_node = of_find_node_by_name(NULL, "ess-switch"); -+ if (!switch_node) { -+ pr_err("switch-node not found\n"); -+ return -EINVAL; -+ } -+ -+ ess_rst = of_reset_control_get(switch_node, "ess_rst"); -+ of_node_put(switch_node); -+ -+ if (IS_ERR(ess_rst)) { -+ pr_err("failed to find ess_rst!\n"); -+ return -ENOENT; -+ } -+ -+ reset_control_assert(ess_rst); -+ msleep(10); -+ reset_control_deassert(ess_rst); -+ msleep(100); -+ reset_control_put(ess_rst); -+ -+ /* Enable only port 5 <--> port 0 -+ * bits 0:6 bitmap of ports it can fwd to */ -+#define SET_PORT_BMP(r,v) \ -+ ess_read_reg(edma, r, ®val); \ -+ ess_write_reg(edma, r, ((regval & ~0x3F) | v)); -+ -+ SET_PORT_BMP(ESS_PORT0_LOOKUP_CTRL,0x20); -+ SET_PORT_BMP(ESS_PORT1_LOOKUP_CTRL,0x00); -+ SET_PORT_BMP(ESS_PORT2_LOOKUP_CTRL,0x00); -+ SET_PORT_BMP(ESS_PORT3_LOOKUP_CTRL,0x00); -+ SET_PORT_BMP(ESS_PORT4_LOOKUP_CTRL,0x00); -+ SET_PORT_BMP(ESS_PORT5_LOOKUP_CTRL,0x01); -+ ess_write_reg(edma, ESS_RGMII_CTRL, 0x400); -+ ess_write_reg(edma, ESS_PORT0_STATUS, ESS_PORT_1G_FDX); -+ ess_write_reg(edma, ESS_PORT5_STATUS, ESS_PORT_1G_FDX); -+ ess_write_reg(edma, ESS_PORT0_HEADER_CTRL, 0); -+#undef SET_PORT_BMP -+ -+ /* forward multicast and broadcast frames to CPU */ -+ ess_write_reg(edma, ESS_FWD_CTRL1, -+ (ESS_PORTS_ALL << ESS_FWD_CTRL1_UC_FLOOD_S) | -+ (ESS_PORTS_ALL << ESS_FWD_CTRL1_MC_FLOOD_S) | -+ (ESS_PORTS_ALL << ESS_FWD_CTRL1_BC_FLOOD_S)); -+ -+ return 0; -+} -+ -+void ess_set_port_status_speed(struct edma_common_info *edma, -+ struct phy_device *phydev, uint8_t port_id) -+{ -+ uint16_t reg_off = ESS_PORT0_STATUS + (4 * port_id); -+ uint32_t reg_val = 0; -+ -+ ess_read_reg(edma, reg_off, ®_val); -+ -+ /* reset the speed bits [0:1] */ -+ reg_val &= ~ESS_PORT_STATUS_SPEED_INV; -+ -+ /* set the new speed */ -+ switch(phydev->speed) { -+ case SPEED_1000: reg_val |= ESS_PORT_STATUS_SPEED_1000; break; -+ case SPEED_100: reg_val |= ESS_PORT_STATUS_SPEED_100; break; -+ case SPEED_10: reg_val |= ESS_PORT_STATUS_SPEED_10; break; -+ default: reg_val |= ESS_PORT_STATUS_SPEED_INV; break; -+ } -+ -+ /* check full/half duplex */ -+ if (phydev->duplex) { -+ reg_val |= ESS_PORT_STATUS_DUPLEX_MODE; -+ } else { -+ reg_val &= ~ESS_PORT_STATUS_DUPLEX_MODE; -+ } -+ -+ ess_write_reg(edma, reg_off, reg_val); -+} -+ - /* edma_change_tx_coalesce() - * change tx interrupt moderation timer - */ -@@ -550,6 +650,31 @@ static struct ctl_table edma_table[] = { - {} - }; - -+static int ess_parse(struct edma_common_info *edma) -+{ -+ struct device_node *switch_node; -+ int ret = -EINVAL; -+ -+ switch_node = of_find_node_by_name(NULL, "ess-switch"); -+ if (!switch_node) { -+ pr_err("cannot find ess-switch node\n"); -+ goto out; -+ } -+ -+ edma->ess_hw_addr = of_io_request_and_map(switch_node, -+ 0, KBUILD_MODNAME); -+ if (!edma->ess_hw_addr) { -+ pr_err("%s ioremap fail.", __func__); -+ goto out; -+ } -+ -+ edma->ess_clk = of_clk_get_by_name(switch_node, "ess_clk"); -+ ret = clk_prepare_enable(edma->ess_clk); -+out: -+ of_node_put(switch_node); -+ return ret; -+} -+ - /* edma_axi_netdev_ops - * Describe the operations supported by registered netdevices - * -@@ -785,6 +910,17 @@ static int edma_axi_probe(struct platfor - miibus = mdio_data->mii_bus; - } - -+ if (of_property_read_bool(np, "qcom,single-phy") && -+ edma_cinfo->num_gmac == 1) { -+ err = ess_parse(edma_cinfo); -+ if (!err) -+ err = ess_reset(edma_cinfo); -+ if (err) -+ goto err_single_phy_init; -+ else -+ edma_cinfo->is_single_phy = true; -+ } -+ - for_each_available_child_of_node(np, pnp) { - const char *mac_addr; - -@@ -1073,11 +1209,15 @@ static int edma_axi_probe(struct platfor - - for (i = 0; i < edma_cinfo->num_gmac; i++) { - if (adapter[i]->poll_required) { -+ int phy_mode = of_get_phy_mode(np); -+ -+ if (phy_mode < 0) -+ phy_mode = PHY_INTERFACE_MODE_SGMII; - adapter[i]->phydev = - phy_connect(edma_netdev[i], - (const char *)adapter[i]->phy_id, - &edma_adjust_link, -- PHY_INTERFACE_MODE_SGMII); -+ phy_mode); - if (IS_ERR(adapter[i]->phydev)) { - dev_dbg(&pdev->dev, "PHY attach FAIL"); - err = -EIO; -@@ -1121,6 +1261,9 @@ err_rmap_alloc_fail: - for (i = 0; i < edma_cinfo->num_gmac; i++) - unregister_netdev(edma_netdev[i]); - err_register: -+err_single_phy_init: -+ iounmap(edma_cinfo->ess_hw_addr); -+ clk_disable_unprepare(edma_cinfo->ess_clk); - err_mdiobus_init_fail: - edma_free_rx_rings(edma_cinfo); - err_rx_rinit: -@@ -1181,6 +1324,8 @@ static int edma_axi_remove(struct platfo - del_timer_sync(&edma_cinfo->edma_stats_timer); - edma_free_irqs(adapter); - unregister_net_sysctl_table(edma_cinfo->edma_ctl_table_hdr); -+ iounmap(edma_cinfo->ess_hw_addr); -+ clk_disable_unprepare(edma_cinfo->ess_clk); - edma_free_tx_resources(edma_cinfo); - edma_free_rx_resources(edma_cinfo); - edma_free_tx_rings(edma_cinfo); ---- a/drivers/net/ethernet/qualcomm/essedma/ess_edma.h -+++ b/drivers/net/ethernet/qualcomm/essedma/ess_edma.h -@@ -329,4 +329,61 @@ struct edma_hw; - #define EDMA_RRD_PRIORITY_MASK 0x7 - #define EDMA_RRD_PORT_TYPE_SHIFT 7 - #define EDMA_RRD_PORT_TYPE_MASK 0x1F -+ -+#define ESS_RGMII_CTRL 0x0004 -+ -+/* Port status registers */ -+#define ESS_PORT0_STATUS 0x007C -+#define ESS_PORT1_STATUS 0x0080 -+#define ESS_PORT2_STATUS 0x0084 -+#define ESS_PORT3_STATUS 0x0088 -+#define ESS_PORT4_STATUS 0x008C -+#define ESS_PORT5_STATUS 0x0090 -+ -+#define ESS_PORT_STATUS_HDX_FLOW_CTL 0x80 -+#define ESS_PORT_STATUS_DUPLEX_MODE 0x40 -+#define ESS_PORT_STATUS_RX_FLOW_EN 0x20 -+#define ESS_PORT_STATUS_TX_FLOW_EN 0x10 -+#define ESS_PORT_STATUS_RX_MAC_EN 0x08 -+#define ESS_PORT_STATUS_TX_MAC_EN 0x04 -+#define ESS_PORT_STATUS_SPEED_INV 0x03 -+#define ESS_PORT_STATUS_SPEED_1000 0x02 -+#define ESS_PORT_STATUS_SPEED_100 0x01 -+#define ESS_PORT_STATUS_SPEED_10 0x00 -+ -+#define ESS_PORT_1G_FDX (ESS_PORT_STATUS_DUPLEX_MODE | ESS_PORT_STATUS_RX_FLOW_EN | \ -+ ESS_PORT_STATUS_TX_FLOW_EN | ESS_PORT_STATUS_RX_MAC_EN | \ -+ ESS_PORT_STATUS_TX_MAC_EN | ESS_PORT_STATUS_SPEED_1000) -+ -+#define PHY_STATUS_REG 0x11 -+#define PHY_STATUS_SPEED 0xC000 -+#define PHY_STATUS_SPEED_SHIFT 14 -+#define PHY_STATUS_DUPLEX 0x2000 -+#define PHY_STATUS_DUPLEX_SHIFT 13 -+#define PHY_STATUS_SPEED_DUPLEX_RESOLVED 0x0800 -+#define PHY_STATUS_CARRIER 0x0400 -+#define PHY_STATUS_CARRIER_SHIFT 10 -+ -+/* Port lookup control registers */ -+#define ESS_PORT0_LOOKUP_CTRL 0x0660 -+#define ESS_PORT1_LOOKUP_CTRL 0x066C -+#define ESS_PORT2_LOOKUP_CTRL 0x0678 -+#define ESS_PORT3_LOOKUP_CTRL 0x0684 -+#define ESS_PORT4_LOOKUP_CTRL 0x0690 -+#define ESS_PORT5_LOOKUP_CTRL 0x069C -+ -+#define ESS_PORT0_HEADER_CTRL 0x009C -+ -+#define ESS_PORTS_ALL 0x3f -+ -+#define ESS_FWD_CTRL1 0x0624 -+#define ESS_FWD_CTRL1_UC_FLOOD BITS(0, 7) -+#define ESS_FWD_CTRL1_UC_FLOOD_S 0 -+#define ESS_FWD_CTRL1_MC_FLOOD BITS(8, 7) -+#define ESS_FWD_CTRL1_MC_FLOOD_S 8 -+#define ESS_FWD_CTRL1_BC_FLOOD BITS(16, 7) -+#define ESS_FWD_CTRL1_BC_FLOOD_S 16 -+#define ESS_FWD_CTRL1_IGMP BITS(24, 7) -+#define ESS_FWD_CTRL1_IGMP_S 24 -+ - #endif /* _ESS_EDMA_H_ */ |