diff options
Diffstat (limited to 'target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts')
| -rw-r--r-- | target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts | 229 |
1 files changed, 0 insertions, 229 deletions
diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts deleted file mode 100644 index 02f60c90ee..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts +++ /dev/null @@ -1,229 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - model = "Qualcomm Technologies, Inc. IPQ8064/AP-148"; - compatible = "qcom,ipq8064-ap148", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - soc { - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - }; - }; -}; - -&qcom_pinmux { - i2c4_pins: i2c4_pinmux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - bias-disable; - }; - - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&gsbi4 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "okay"; - - serial@16340000 { - status = "okay"; - }; - - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ -}; - -&gsbi5 { - qcom,mode = <GSBI_PROT_SPI>; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - spi-max-frequency = <50000000>; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 0>; - - flash: m25p80@0 { - compatible = "s25fl256s1"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; -}; - -&usb3_0 { - status = "okay"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - force_gen1 = <1>; -}; - -&nand { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "qcom,smem"; - }; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&sata_phy { - status = "okay"; -}; - -&sata { - status = "okay"; -}; |