aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux')
-rwxr-xr-xtarget/linux/kirkwood/base-files/etc/board.d/02_network3
-rwxr-xr-xtarget/linux/kirkwood/base-files/etc/board.d/03_gpio_switches18
-rw-r--r--target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac25
-rw-r--r--target/linux/kirkwood/config-5.41
-rw-r--r--target/linux/kirkwood/image/Makefile10
-rw-r--r--target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch485
-rw-r--r--target/linux/kirkwood/patches-5.4/111-l-50.patch47
7 files changed, 589 insertions, 0 deletions
diff --git a/target/linux/kirkwood/base-files/etc/board.d/02_network b/target/linux/kirkwood/base-files/etc/board.d/02_network
index a86c57117d..658ce13346 100755
--- a/target/linux/kirkwood/base-files/etc/board.d/02_network
+++ b/target/linux/kirkwood/base-files/etc/board.d/02_network
@@ -11,6 +11,9 @@ board_config_update
board=$(board_name)
case "$board" in
+"checkpoint,l-50")
+ ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 dmz" "eth0"
+ ;;
"cisco,on100")
ucidef_set_interface_lan "eth0 eth1"
;;
diff --git a/target/linux/kirkwood/base-files/etc/board.d/03_gpio_switches b/target/linux/kirkwood/base-files/etc/board.d/03_gpio_switches
new file mode 100755
index 0000000000..046f8d4d20
--- /dev/null
+++ b/target/linux/kirkwood/base-files/etc/board.d/03_gpio_switches
@@ -0,0 +1,18 @@
+#!/bin/sh
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+checkpoint,l-50)
+ ucidef_add_gpio_switch "mpcie-rst" "mPCIE Card reset" "502" "1"
+ ucidef_add_gpio_switch "exp-card-rst" "Express Card reset" "497" "1"
+ ;;
+esac
+
+board_config_flush
+
+exit 0
diff --git a/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac b/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac
new file mode 100644
index 0000000000..75e9e886d9
--- /dev/null
+++ b/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac
@@ -0,0 +1,25 @@
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+preinit_set_mac_address() {
+ local mac
+
+ case $(board_name) in
+ checkpoint,l-50)
+ mac=$(mtd_get_mac_ascii bootldr-env lan1_mac_addr)
+
+ ip link set dev lan1 address $mac 2>/dev/null
+ ip link set dev lan2 address $(macaddr_add $mac 1) 2>/dev/null
+ ip link set dev lan3 address $(macaddr_add $mac 2) 2>/dev/null
+ ip link set dev lan4 address $(macaddr_add $mac 3) 2>/dev/null
+ ip link set dev lan5 address $(macaddr_add $mac 4) 2>/dev/null
+ ip link set dev lan6 address $(macaddr_add $mac 5) 2>/dev/null
+ ip link set dev lan7 address $(macaddr_add $mac 6) 2>/dev/null
+ ip link set dev lan8 address $(macaddr_add $mac 7) 2>/dev/null
+ ip link set dev dmz address $(macaddr_add $mac 8) 2>/dev/null
+ ip link set dev dsl address $(macaddr_add $mac 9) 2>/dev/null
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main preinit_set_mac_address
diff --git a/target/linux/kirkwood/config-5.4 b/target/linux/kirkwood/config-5.4
index 5529bf89df..61efa07d91 100644
--- a/target/linux/kirkwood/config-5.4
+++ b/target/linux/kirkwood/config-5.4
@@ -282,6 +282,7 @@ CONFIG_PINCTRL=y
CONFIG_PINCTRL_KIRKWOOD=y
CONFIG_PINCTRL_MVEBU=y
# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_PINCTRL_SX150X=y
CONFIG_PLAT_ORION=y
CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_GPIO=y
diff --git a/target/linux/kirkwood/image/Makefile b/target/linux/kirkwood/image/Makefile
index 8cc69195b4..ba93fffeb2 100644
--- a/target/linux/kirkwood/image/Makefile
+++ b/target/linux/kirkwood/image/Makefile
@@ -28,6 +28,16 @@ define Device/Default
SUPPORTED_DEVICES = $(subst _,$(comma),$(1)) $$(BOARD_NAME)
endef
+define Device/checkpoint_l-50
+ DEVICE_VENDOR := Check Point
+ DEVICE_MODEL := L-50
+ DEVICE_DTS := kirkwood-l-50
+ DEVICE_PACKAGES := kmod-ath9k kmod-gpio-button-hotplug kmod-mvsdio \
+ kmod-rtc-s35390a kmod-usb-ledtrig-usbport wpad-basic
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += checkpoint_l-50
+
define Device/cisco_on100
DEVICE_VENDOR := Cisco Systems
DEVICE_MODEL := ON100
diff --git a/target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch b/target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch
new file mode 100644
index 0000000000..52caee7b40
--- /dev/null
+++ b/target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch
@@ -0,0 +1,485 @@
+From efa968c18abab78c5e0c40a853caf286c3629a59 Mon Sep 17 00:00:00 2001
+From: Pawel Dembicki <paweldembicki@gmail.com>
+Date: Tue, 17 Mar 2020 21:28:01 +0100
+Subject: [PATCH v3] ARM: dts: kirkwood: Add Check Point L-50 board
+
+This patch adds dts for the Check Point L-50 from 600/1100 series
+routers.
+
+Specification:
+-CPU: Marvell Kirkwood 88F6821 1200MHz
+-RAM: 512MB
+-Flash: NAND 512MB
+-WiFi: mPCIe card based on Atheros AR9287 b/g/n
+-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
+-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+3))
+-USB: 2x USB2.0
+-Express card slot
+-SD card slot
+-Serial console: RJ-45 115200 8n1
+-Unsupported DSL
+
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
+---
+Changes in v3:
+- fix typo and code style issues pointed by OpenWrt guys
+Changes in v2:
+- none
+
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/kirkwood-l-50.dts | 438 ++++++++++++++++++++++++++++
+ 2 files changed, 439 insertions(+)
+ create mode 100644 arch/arm/boot/dts/kirkwood-l-50.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -270,6 +270,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ kirkwood-iomega_ix2_200.dtb \
+ kirkwood-is2.dtb \
+ kirkwood-km_kirkwood.dtb \
++ kirkwood-l-50.dtb \
+ kirkwood-laplug.dtb \
+ kirkwood-linkstation-lsqvl.dtb \
+ kirkwood-linkstation-lsvl.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-l-50.dts
+@@ -0,0 +1,438 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Check Point L-50 Board Description
++ * Copyright 2020 Pawel Dembicki <paweldembicki@gmail.com>
++ */
++
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6281.dtsi"
++
++/ {
++ model = "Check Point L-50";
++ compatible = "checkpoint,l-50", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++ memory {
++ device_type = "memory";
++ reg = <0x00000000 0x20000000>;
++ };
++
++ chosen {
++ bootargs = "console=ttyS0,115200n8";
++ stdout-path = &uart0;
++ };
++
++ ocp@f1000000 {
++ pinctrl: pin-controller@10000 {
++ pinctrl-0 = <&pmx_led38 &pmx_sysrst &pmx_button29>;
++ pinctrl-names = "default";
++
++ pmx_sysrst: pmx-sysrst {
++ marvell,pins = "mpp6";
++ marvell,function = "sysrst";
++ };
++
++ pmx_button29: pmx_button29 {
++ marvell,pins = "mpp29";
++ marvell,function = "gpio";
++ };
++
++ pmx_led38: pmx_led38 {
++ marvell,pins = "mpp38";
++ marvell,function = "gpio";
++ };
++
++ pmx_sdio_cd: pmx-sdio-cd {
++ marvell,pins = "mpp46";
++ marvell,function = "gpio";
++ };
++ };
++
++ serial@12000 {
++ status = "okay";
++ };
++
++ mvsdio@90000 {
++ status = "okay";
++ cd-gpios = <&gpio1 14 9>;
++ };
++
++ i2c@11000 {
++ status = "okay";
++ clock-frequency = <400000>;
++
++ gpio2: gpio-expander@20{
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ compatible = "semtech,sx1505q";
++ reg = <0x20>;
++
++ gpio-controller;
++ };
++
++ /* Three GPIOs from 0x21 exp. are undescribed in dts:
++ * 1: DSL module reset (active low)
++ * 5: mPCIE reset (active low)
++ * 6: Express card reset (active low)
++ */
++ gpio3: gpio-expander@21{
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ compatible = "semtech,sx1505q";
++ reg = <0x21>;
++
++ gpio-controller;
++ };
++
++ rtc@30 {
++ compatible = "s35390a";
++ reg = <0x30>;
++ };
++ };
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ status_green {
++ label = "l-50:green:status";
++ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
++ };
++
++ status_red {
++ label = "l-50:red:status";
++ gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
++ };
++
++ wifi {
++ label = "l-50:green:wifi";
++ gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "phy0tpt";
++ };
++
++ internet_green {
++ label = "l-50:green:internet";
++ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
++ };
++
++ internet_red {
++ label = "l-50:red:internet";
++ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
++ };
++
++ usb1_green {
++ label = "l-50:green:usb1";
++ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "usbport";
++ trigger-sources = <&hub_port3>;
++ };
++
++ usb1_red {
++ label = "l-50:red:usb1";
++ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
++ };
++
++ usb2_green {
++ label = "l-50:green:usb2";
++ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "usbport";
++ trigger-sources = <&hub_port1>;
++ };
++
++ usb2_red {
++ label = "l-50:red:usb2";
++ gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ usb2_pwr {
++ compatible = "regulator-fixed";
++ regulator-name = "usb2_pwr";
++
++ regulator-min-microvolt = <5000000>;
++ regulator-max-microvolt = <5000000>;
++ gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
++ regulator-always-on;
++ };
++
++ usb1_pwr {
++ compatible = "regulator-fixed";
++ regulator-name = "usb1_pwr";
++
++ regulator-min-microvolt = <5000000>;
++ regulator-max-microvolt = <5000000>;
++ gpio = <&gpio3 4 GPIO_ACTIVE_LOW>;
++ regulator-always-on;
++ };
++
++ mpcie_pwr {
++ compatible = "regulator-fixed";
++ regulator-name = "mpcie_pwr";
++
++ regulator-min-microvolt = <3300000>;
++ regulator-max-microvolt = <3300000>;
++ gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
++ enable-active-high;
++ regulator-always-on;
++ };
++
++ express_card_pwr {
++ compatible = "regulator-fixed";
++ regulator-name = "express_card_pwr";
++
++ regulator-min-microvolt = <3300000>;
++ regulator-max-microvolt = <3300000>;
++ gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
++ enable-active-high;
++ regulator-always-on;
++ };
++
++ keys {
++ compatible = "gpio-keys";
++
++ factory_defaults {
++ label = "factory_defaults";
++ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
++ linux,code = <KEY_RESTART>;
++ };
++ };
++};
++
++&mdio {
++ status = "okay";
++
++ ethphy8: ethernet-phy@8 {
++ reg = <0x08>;
++ };
++
++ switch0: switch@10 {
++ compatible = "marvell,mv88e6085";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ reg = <0x10>;
++ dsa,member = <0 0>;
++
++ ports {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ port@0 {
++ reg = <0>;
++ label = "lan5";
++ };
++
++ port@1 {
++ reg = <1>;
++ label = "lan1";
++ };
++
++ port@2 {
++ reg = <2>;
++ label = "lan6";
++ };
++
++ port@3 {
++ reg = <3>;
++ label = "lan2";
++ };
++
++ port@4 {
++ reg = <4>;
++ label = "lan7";
++ };
++
++ switch0port5: port@5 {
++ reg = <5>;
++ phy-mode = "rgmii-txid";
++ link = <&switch1port5>;
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++
++ port@6 {
++ reg = <6>;
++ label = "cpu";
++ phy-mode = "rgmii-id";
++ ethernet = <&eth1port>;
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++ };
++ };
++
++ switch@11 {
++ compatible = "marvell,mv88e6085";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ reg = <0x11>;
++ dsa,member = <0 1>;
++
++ ports {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ port@0 {
++ reg = <0>;
++ label = "lan3";
++ };
++
++ port@1 {
++ reg = <1>;
++ label = "lan8";
++ };
++
++ port@2 {
++ reg = <2>;
++ label = "lan4";
++ };
++
++ port@3 {
++ reg = <3>;
++ label = "dmz";
++ };
++
++ switch1port5: port@5 {
++ reg = <5>;
++ phy-mode = "rgmii-txid";
++ link = <&switch0port5>;
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++
++ port@6 {
++ reg = <6>;
++ label = "dsl";
++ fixed-link {
++ speed = <100>;
++ full-duplex;
++ };
++ };
++ };
++ };
++};
++
++&eth0 {
++ status = "okay";
++ ethernet0-port@0 {
++ phy-handle = <&ethphy8>;
++ };
++};
++
++&eth1 {
++ status = "okay";
++ ethernet1-port@0 {
++ speed = <1000>;
++ duplex = <1>;
++ };
++};
++
++&nand {
++ status = "okay";
++ pinctrl-0 = <&pmx_nand>;
++ pinctrl-names = "default";
++
++ partition@0 {
++ label = "u-boot";
++ reg = <0x00000000 0x000c0000>;
++ };
++
++ partition@a0000 {
++ label = "bootldr-env";
++ reg = <0x000c0000 0x00040000>;
++ };
++
++ partition@100000 {
++ label = "kernel-1";
++ reg = <0x00100000 0x00800000>;
++ };
++
++ partition@900000 {
++ label = "rootfs-1";
++ reg = <0x00900000 0x07100000>;
++ };
++
++ partition@7a00000 {
++ label = "kernel-2";
++ reg = <0x07a00000 0x00800000>;
++ };
++
++ partition@8200000 {
++ label = "rootfs-2";
++ reg = <0x08200000 0x07100000>;
++ };
++
++ partition@f300000 {
++ label = "default_sw";
++ reg = <0x0f300000 0x07900000>;
++ };
++
++ partition@16c00000 {
++ label = "logs";
++ reg = <0x16c00000 0x01800000>;
++ };
++
++ partition@18400000 {
++ label = "preset_cfg";
++ reg = <0x18400000 0x00100000>;
++ };
++
++ partition@18500000 {
++ label = "adsl";
++ reg = <0x18500000 0x00100000>;
++ };
++
++ partition@18600000 {
++ label = "storage";
++ reg = <0x18600000 0x07a00000>;
++ };
++};
++
++&rtc {
++ status = "disabled";
++};
++
++&pciec {
++ status = "okay";
++};
++
++&pcie0 {
++ status = "okay";
++};
++
++&sata_phy0 {
++ status = "disabled";
++};
++
++&sata_phy1 {
++ status = "disabled";
++};
++
++&usb0 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ status = "okay";
++
++ port@1 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ reg = <1>;
++ #trigger-source-cells = <0>;
++
++ hub_port1: port@1 {
++ reg = <1>;
++ #trigger-source-cells = <0>;
++ };
++
++ hub_port3: port@3 {
++ reg = <3>;
++ #trigger-source-cells = <0>;
++ };
++ };
++};
diff --git a/target/linux/kirkwood/patches-5.4/111-l-50.patch b/target/linux/kirkwood/patches-5.4/111-l-50.patch
new file mode 100644
index 0000000000..b1679885ad
--- /dev/null
+++ b/target/linux/kirkwood/patches-5.4/111-l-50.patch
@@ -0,0 +1,47 @@
+--- a/arch/arm/boot/dts/kirkwood-l-50.dts
++++ b/arch/arm/boot/dts/kirkwood-l-50.dts
+@@ -18,6 +18,13 @@
+ reg = <0x00000000 0x20000000>;
+ };
+
++ aliases {
++ led-boot = &led_status_green;
++ led-failsafe = &led_status_red;
++ led-running = &led_status_green;
++ led-upgrade = &led_status_red;
++ };
++
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ stdout-path = &uart0;
+@@ -95,12 +102,12 @@
+ leds {
+ compatible = "gpio-leds";
+
+- status_green {
++ led_status_green: status_green {
+ label = "l-50:green:status";
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ };
+
+- status_red {
++ led_status_red: status_red {
+ label = "l-50:red:status";
+ gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+ };
+@@ -349,13 +356,8 @@
+ };
+
+ partition@100000 {
+- label = "kernel-1";
+- reg = <0x00100000 0x00800000>;
+- };
+-
+- partition@900000 {
+- label = "rootfs-1";
+- reg = <0x00900000 0x07100000>;
++ label = "ubi";
++ reg = <0x00100000 0x07900000>;
+ };
+
+ partition@7a00000 {