aboutsummaryrefslogtreecommitdiffstats
path: root/package/kernel
Commit message (Collapse)AuthorAgeFilesLines
* package: drop PKG_VERSION for purely local packagesAdrian Schmutzler2020-07-152-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the package guidelines, PKG_VERSION is supposed to be used as "The upstream version number that we're downloading", while PKG_RELEASE is referred to as "The version of this package Makefile". Thus, the variables in a strict interpretation provide a clear distinction between "their" (upstream) version in PKG_VERSION and "our" (local OpenWrt trunk) version in PKG_RELEASE. For local (OpenWrt-only) packages, this implies that those will only need PKG_RELEASE defined, while PKG_VERSION does not apply following a strict interpretation. While the majority of "our" packages actually follow that scheme, there are also some that mix both variables or have one of them defined but keep them at "1". This is misleading and confusing, which can be observed by the fact that there typically either one of the variables is never bumped or the choice of the variable to increase depends on the person doing the change. Consequently, this patch aims at clarifying the situation by consistently using only PKG_RELEASE for "our" packages. To achieve that, PKG_VERSION is removed there, bumping PKG_RELEASE where necessary to ensure the resulting package version string is bigger than before. During adjustment, one has to make sure that the new resulting composite package version will not be considered "older" than the previous one. A useful tool for evaluating that is 'opkg compare-versions'. In principle, there are the following cases: 1. Sole PKG_VERSION replaced by sole PKG_RELEASE: In this case, the resulting version string does not change, it's just the value of the variable put in the file. Consequently, we do not bump the number in these cases so nobody is tempted to install the same package again. 2. PKG_VERSION and PKG_RELEASE replaced by sole PKG_RELEASE: In this case, the resulting version string has been "version-release", e.g. 1-3 or 1.0-3. For this case, the new PKG_RELEASE will just need to be higher than the previous PKG_VERSION. For the cases where PKG_VERSION has always sticked to "1", and PKG_RELEASE has been incremented, we take the most recent value of PKG_RELEASE. Apart from that, a few packages appear to have developed their own complex versioning scheme, e.g. using x.y.z number for PKG_VERSION _and_ a PKG_RELEASE (qos-scripts) or using dates for PKG_VERSION (adb-enablemodem, wwan). I didn't touch these few in this patch. Cc: Hans Dedecker <dedeckeh@gmail.com> Cc: Felix Fietkau <nbd@nbd.name> Cc: Andre Valentin <avalentin@marcant.net> Cc: Matthias Schiffer <mschiffer@universe-factory.net> Cc: Jo-Philipp Wich <jo@mein.io> Cc: Steven Barth <steven@midlink.org> Cc: Daniel Golle <dgolle@allnet.de> Cc: John Crispin <john@phrozen.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ltq-vmmc: update permission handlingSebastian Kemper2020-07-112-13/+7
| | | | | | | | | | | | | | The firmware is currently just copied. It can end up with o= on the device (this is the case for voice_ar9_firmware.bin for instance). Instead of copying it the Makefile is changed to use the macro "$(INSTALL_DATA)" in order for the file to be world-readable. While at it refactor the device node creation in the init script with loop. Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net> [removed 2nd part with custom group handling for device nodes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: kmod-zram: break the strict dependency from lz4Rui Salvaterra2020-07-112-4/+2
| | | | | | | | Zram is only strictly dependent on lzo, not lz4. Break this dependency and make the lz4 module visible in the configuration, in order for the user to have the choice of enabling/disabling it, if (s)he sees fit. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* linux-firmware: package EIP197 mini firmwareTomasz Maciej Nowak2020-07-111-4/+6
| | | | | | | | | | | | | Quoting part of original message from eefb5f741015 commit in linux-firmware repository: This adds the "minifw" version of the EIP197 firmware, which the inside- secure driver will use as a fallback if the original full-featured firmware cannot be found. This allows for using the inside-secure driver and hardware without access to "official" firmware only available under NDA. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* kernel: add package for Seiko S-35390A I2C RTCPawel Dembicki2020-07-111-0/+17
| | | | | | This patch adds kernel package for Seiko Instruments S-35390A. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* mac80211: rt2x00: define RF5592 in init_eeprom routineDaniel Golle2020-07-103-3/+54
| | | | | | | | | | | Make sure RF5592 is set for RT5592 chip which apparently sometimes doesn't have RF defined (but always comes with RF5592). This patch was originally submitted on linux-wireless by Tom Psyborg <pozega.tomislav@gmail.com> but got rejected. Turns out the patch is actually needed. Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: iscsi-initator: fix kernel config symbolsLucian Cristian2020-07-091-2/+2
| | | | | | | | | | | | | | | Enable SCSI low-level drivers on targets that don't have it already in order to fix following build failures on few platforms: .config:4739:warning: symbol value 'm' invalid for SCSI_LOWLEVEL * Restart config... * SCSI low-level drivers SCSI low-level drivers (SCSI_LOWLEVEL) [Y/n] (NEW) aborted! Fixes: b88f8202c4ce ("kernel: add iscsi-initator support") Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com> [commit subject and description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: iscsi-initator: fix missing dependencyPetr Štetiar2020-07-081-1/+1
| | | | | | | | | | Fixes following issue: Package kmod-iscsi-initiator is missing dependencies for the following libraries: crypto_hash.ko Fixes: b88f8202c4ce ("kernel: add iscsi-initator support") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mt7621-qtn-rgmii: enable RGMII connected Quantenna QV840Bjørn Mork2020-07-083-0/+94
| | | | | | | Write a magic value to a magic destination. This might be specific to the Mitrastar designed ZyXEL WAP6805. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kernel: add iscsi-initator supportLucian Cristian2020-07-081-0/+26
| | | | | | | | Module is needed for using iscsi-initiator userspace applications Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com> [added missing newline between kernel modules] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* nat46: fix translation of ICMP protocol unreachableHans Dedecker2020-07-072-5/+5
| | | | | | | | Refresh patch 1182f30 nat46-core: Fix translation of ICMP protocol unreachable Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mac80211: allow ACS restriction with fixed channelJan Hoffmann2020-07-061-1/+1
| | | | | | | | | | | This can be useful when a DFS channel is configured, as the ACS channel list is taken into account when switching channels after a radar event. For example, this allows to prevent the SRD channels from being used in that case. Signed-off-by: Jan Hoffmann <jan@3e8.eu> [reorder structure] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath10k-ct: update to version 2020-06-30Álvaro Fernández Rojas2020-07-014-14/+14
| | | | | | | | Backports commit "a1769bb68a850508a492e3674ab1e5e479b11254", which reverts upstream commit "76d164f582150fd0259ec0fcbc485470bcd8033e" (ath10k: fix DMA related firmware crashes on multiple devices). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: i2c-pxa: remove slaveScott Roberts2020-06-271-1/+0
| | | | | | | | | | | | | | | | Removing i2c pxa slave The i2c-pxa is typically not use in slave mode. It does not make sense to have slave mode enabled by default. Having slave mode enabled prevents the i2c controller from being reset if a real slave device such as an SFP is attached to the i2c-pxa bus and locks it up. Disable slave mode so that the i2c controller can be reset if the bus is locked up. If someone actually has a need for pxa slave mode this can be enabled in kernel config. Signed-off-by: Scott Roberts <ttocsr@gmail.com>
* kernel: add gpio-amd-fch module descriptionFlorian Eckert2020-06-261-0/+17
| | | | | | Add a module description for the new gpio-amd-fch device driver. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* kernel/leds-apu2: remove deprecated leds-apu2 driverFlorian Eckert2020-06-264-423/+0
| | | | | | | | Remove leds-apu2 out of tree driver. There is a new upstream device gpio and leds driver stack available for the APUv2 and APUv3 boards from pc egnines. This new driver stack was add in kernel version 4.15. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* mac80211: ath9k: enable MFP capability unconditionallyDavid Bauer2020-06-251-0/+34
| | | | | | | | | | ath9k will already fallback on software-crypto for chipsets not supporting IEEE802.11w (MFP). So advertising MFP is not dependent on disabling HW crypto for all traffic entirely. Tested on Sonicwall SonicPoint Ni (AR9132) Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: fix use of local variableLeon M. George2020-06-241-1/+1
| | | | | | | | | | mac80211_get_addr is called from mac80211_generate_mac, where the local variable initialisation id="${macidx:-0}" suggests that macidx is not always defined. Probably, idx was supposed to be used instead of $(($macidx + 1)). Fixes: 4d99db168cf7 ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set") Signed-off-by: Leon M. George <leon@georgemail.eu>
* mac80211: ath9k: enable adding wireless noise to kernel entropy poolAlan Swanson2020-06-181-0/+8
| | | | | | | | | | This option allows adding the ath9k ADC register output as a source of randomness into the Linux entropy pool at sufficient quality random data (at least 10 bits and up to 22 bits of min-entropy for a 32-bit value). Fixes FS#1444 Signed-off-by: Alan Swanson <reiver@improbability.net>
* kirkwood: move mmc/sd features to modulesPawel Dembicki2020-06-141-0/+17
| | | | | | | | | | All devices are using nand images. Built-in MMC/SD modules are not needed anymore. Run tested: pogo v4 Reviewed-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* mt76: enable hostapd 802.11ax support if kmod-mt7915e is selectedFelix Fietkau2020-06-101-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm27xx-gpu-fw: bump to most recent good versionStijn Tintel2020-06-071-14/+14
| | | | | | | | This updates to the last firmware version before the switch to building from the common firmware branch, which introduces various issues. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
* Revert "bcm27xx-gpu-fw: update to latest version"Stijn Tintel2020-06-071-15/+15
| | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 9e467a764b4e30a04dd0431ea277f6acd26babe0. The Raspberry Pi firmware recently switched to building from the common firmware branch. This introduces changes in the core clock handling, causing various issues. E.g. enable_uart=1 no longer fixes the core clock frequency to 250MHz. When the disable-bt DT overlay is not loaded, the core clock frequency is increased to 400MHz. As a result, the UART baud rate is no longer correct, and this causes garbled serial console, or communication problems with HATs that use the UART. As a workaround, the core clock could be fixed to 250MHz by adding 'core_freq=250' in /boot/config.txt, but as there appear to be other issues than just the UART being broken, the safer bet is to revert the firmware for now. Upstream bug: https://github.com/raspberrypi/firmware/issues/1376 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: Add kmod-sch-cake-virtual intermediate packageToke Høiland-Jørgensen2020-06-061-3/+15
| | | | | | | | | | | | As reported in https://github.com/openwrt/packages/issues/12072, the imagebuilder fails due to a dependency resolution error when the userspace packages are built using a target that has a different kernel version than that which is being run. To resolve this, add a virtual kernel package with the conditional dependency currently used in sqm-scripts. The idea is to move the sqm-scripts dependency to this virtual package, which hopefully should be consistent with the actual kernel module being built. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
* hostapd: add support for wifi-station and wifi-vlan sectionsJohn Crispin2020-06-041-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for 2 new uci sections. config wifi-vlan # iface is optional. if it is not defined the vlan will apply # to all interfaces option iface default_radio0 option name guest option vid 100 option network guest config wifi-station # iface is optional. if it is not defined the station will apply # to all interfaces option iface default_radio0 # mac is optional. if it is not defined it will be a catch all # for any sta using this key option mac '00:11:22:33:44:55' # vid is optional. if it is not defined, the sta will be part of # the primary iface. option vid 100 option key testtest With this patch applied it is possible to use multiple PSKs on a single BSS. Signed-off-by: John Crispin <john@phrozen.org>
* kernel: iio: add drivers for st_lsm6dsx IMU MEMS sensorsTim Harvey2020-06-031-0/+48
| | | | | | | | Add kmod for the ST LSM6DSX IMU driver. Signed-off-by: Tim Harvey <tharvey@gateworks.com> [fixed missing regmap module dependencies] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: iio: fix st_accel_{i2c, spi} driverTim Harvey2020-06-031-21/+25
| | | | | | | Add missing kernel module and rename driver Fixes: 2d8f4c4fbd46 ("kernel: iio: add st-accel driver modules") Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* kernel: add gpio-it87Florian Eckert2020-06-031-0/+18
| | | | | | | | | | | | | | | Since commit 910df3f06cc902ca2cb0ca8e963e9354c930df1a we have build in on all X86/64 platforms the gpio-it87 driver. Since this change I am getting the following error message on boot. > kern.err kernel: [ 1.009416] gpio_it87: no device I do not have this device on my system. To prevent the nonsensical message and the loading of the module I have added this as a package, so that it can be installed later or during image building. Signed-off-by: Florian Eckert <fe@dev.tdt.de> Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
* mt76: update to the latest version (adds 7663e, 7663u, 7915 drivers)Felix Fietkau2020-05-311-10/+87
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 7aabfd0c9282 mt7615: add CONFIG_MT76_LEDS to cflags 10a5b7630a37 mt76: mt7615: fix getting maximum tx power from eeprom 8688ed70c987 mt76: mt7615: use module parameter option for offload firmware preference 04798aab1257 net: mt7603: remove duplicate error message 9636177117d8 mt76: mt7615: fix ssid configuration in mt7615_mcu_hw_scan d4ba139d8b8b mt76: mt7615: introduce mt7615_check_offload_capability routine 2cc0d54b65a1 mt76: mt7615: do not mark sched_scan disabled in mt7615_scan_work 5b73be962388 mt76: mt7615: add passive mode for hw scan 96e429e18174 mt76: mt7615: free pci_vector if mt7615_pci_probe fails 8fddbf6390ac mt76: mt7615: introduce support for hardware beacon filter f2c760177bdd mt76: mt7615: introduce mt7615_mcu_set_hif_suspend mcu command db454605106f mt76: mt7615: add WoW support 20b87321c39f mt76: mt7663u: introduce suspend/resume to mt7663u 20db7e73c586 mt76: mt7615: introduce PM support 523716bba561 mt76: mt7615: add gtk rekey offload support 50d377a825cc mt76: mt7615: introduce beacon_loss mcu event 4ef1957cea35 mt76: mt7663: read tx streams from eeprom f25a43cc53e7 mt76: mt7615: check return value of mt7615_eeprom_get_power_index 0a9f71652927 mt76: mt7615: fix ibss mode for mt7663 83f2ba3101b4 mt76: mt7663: fix target power parsing 3e6968593b61 mt76: mt7615: fix delta tx power for mt7663 c1d3ad194ae4 mt76: mt7663: introduce WoW with net detect support 891136ab99da mt76: mt7663: add support to sched scan with randomise addr 82e4d3ebe967 mt76: mt7615: scan all channels if not specified 690b84821cd3 mt76: avoid rx reorder buffer overflow f0117d3107b4 mt76: add support for HE RX rate reporting cc68782bab1a mt76: add Rx stats support for radiotap 3ec47f2fba61 mt76: adjust wcid size to support new 802.11ax generation 0a9f4173dd07 mt76: add HE phy modes and hardware queue c6b002bcdfa6 mt76: add mac80211 driver for MT7915 PCIe-based chipsets b96af5039581 mt76: mt7915: enable Rx HE rate reporting 230054096155 mt76: mt7915: implement HE per-rate tx power support c8f4b6cf1add mt76: mt7915: register per-phy HE capabilities for each interface de1e8af96e19 mt76: mt7915: add HE bss_conf support for interfaces 135a5085932b mt76: mt7915: add HE capabilities support for peers 3b5d908dae2f mt76: mt7915: add Rx radiotap header support 158253e2c11e mt76: mt7915: add .sta_add_debugfs support 7f40e8c2b98d mt76: mt7915: add .sta_statistics support a5368e5cad11 mt76: mt7915: set peer Tx fixed rate through debugfs 4f79c516be5c mt76: mt7915: add tsf related callbacks 509fceb43235 mt76: mt7915: enable firmware module debug support 56405976fc7b mt76: set runtime stream caps by mt76_phy 6bbf1a35c0da linux-firmware: add rebb firmware for mt7663 d7a10094c4e5 mt7663: add client offload firmware 9200732e8534 mt76: mt7663u: copy key pointer in mt7663u_mac_write_txwi 3aa810bde810 mt76: mt7663u: add missing register definitions e236ea5be344 mt76: mt7615: usb: cancel ps work stopping the vif 1d0903de2131 mt76: mt7915: introduce mt7915_get_he_phy_cap 095c72c81c74 mt76: mt7915: add Tx beamformer support 5f9e7664cd26 mt76: mt7915: add Tx beamformee support ac505404c385 mt76: mt7915: add TxBF capabilities 6656bebd39cd mt76: mt7915: add debugfs to track TxBF status 9590db025475 mt76: mt7915: allocate proper size for tlv tags 26eb1ed65987 mt76: mt7915: fix possible deadlock in mt7915_stop f85c1f3fc189 firmware: add mt7915 firmware 9b07251b00b0 mt76: mt7615: fix typo defining ps work 060e375a9244 mt76: fix per-driver wcid range checks after wcid array size bump 7270b56389a9 mt76: mt7615: do not report scan_complete twice to mac80211 8c9e4847d01e mt76: mt7615: reduce hw scan timeout 8bd88a1b1880 mt76: enable p2p support 1ea444d0e8e5 mt76: mt7615: configure bss info adding the interface fa81da5bb4e9 mt76: mt7615: introduce remain_on_channel support 44f2262c0289 mt76: mt76x02: remove check in mt76x02_mcu_msg_send 7005aa891440 mt76: mt7915: add spatial reuse support 1e3dc5b76649 mt76: mt7915: fix some sparse warnings 01b784174cd5 mt76: mt7915: fix sparse warnings: incorrect type initializer 40b7b5354a16 mt76: mt7615: fix NULL pointer deref in mt7615_register_ext_phy 6d731d188d31 mt76: mt7915: fix decoded radiotap HE flags b74d5b1c14cf mt76: mt7915: fix some sparse warnings 6679d35be5cc mt76: mt7615: switch to per-vif power_save support 01e870b44769 mt76: mt7915: fix a handful of spelling mistakes 7b2d16655904 mt76: mt7663: fix the usage WoW with net detect support ed3a244fb647 mt76: mt7915: Fix build error 5396a61cec99 mt76: mt7615: fix hw_scan with ssid_type for specified SSID only 466a5b4d041d mt76: mt7915: fix possible NULL pointer dereference in mt7915_register_ext_phy 984a172609c0 mt76: fix wcid allocation issues 6e02acddcb1a mt76: mt7615: add support for MT7611N 4e6f4e432d0d mt76: only iterate over initialized rx queues 9ad940fee593 mt76: mt7615: Use kmemdup in mt7615_queue_key_update() 85c516081338 mt76: mt7915: remove set but not used variable 'msta' Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix wifi teardownJohn Crispin2020-05-301-4/+6
| | | | | | reverts part of the recent wifi reconf patch. Signed-off-by: John Crispin <john@phrozen.org>
* mac80211: rt2x00: backport patch enabling MFPDaniel Golle2020-05-301-0/+44
| | | | | | | | | | | | From: Rui Salvaterra <rsalvaterra@gmail.com> Date: Mon, 25 May 2020 14:49:07 +0100 Subject: [PATCH] rt2800: enable MFP support unconditionally This gives us WPA3 support out of the box without having to manually disable hardware crypto. The driver will fall back to software crypto if the connection requires management frame protection. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: Fix setting radio htmode when using mesh modeEnrique Rodríguez Valencia2020-05-281-0/+1
| | | | | | | When configuring the radio in legacy mode from luci, the htmode is not set correctly to NOHT, causing the radio in mesh mode to be set to HT40. Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
* broadcom-wl: don't inherit lock descriptor in nas processJo-Philipp Wich2020-05-282-2/+5
| | | | | | | | | | | Add a local hack to prevent the Broadcom WPA authenticator process from inheriting the lock descriptor 1000 used to prevent concurrent executions of the init script. Without this fix, repeated invocations of /etc/init.d/network, e.g. for obtaining the enabled state, would hang forever. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* bcm27xx-gpu-fw: update to latest versionÁlvaro Fernández Rojas2020-05-281-15/+15
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mac80211: Fix build on mpc85xx targetHauke Mehrtens2020-05-212-1/+32
| | | | | | | | | | | | | | | | | | | | | | | | | This fixes the following compile error seen on the mpc85xx target: CC [M] /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o In file included from /builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/stddef.h:17, from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/uapi/linux/wireless.h:77, from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/linux/wireless.h:13, from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:89: /builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/alltypes.h:106:15: error: conflicting types for 'ptrdiff_t' typedef _Addr ptrdiff_t; ^~~~~~~~~ In file included from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/types.h:4, from ./include/linux/list.h:5, from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/list.h:3, from ./include/linux/module.h:9, from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/module.h:3, from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:79: ./include/linux/types.h:65:28: note: previous declaration of 'ptrdiff_t' was here typedef __kernel_ptrdiff_t ptrdiff_t; ^~~~~~~~~ scripts/Makefile.build:265: recipe for target '/linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o' failed Fixes: 289c6324259e ("mac80211: Update to version 5.7-rc3-1") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Update to version 5.7-rc3-1Hauke Mehrtens2020-05-2123-291/+140
| | | | | | | | | | | This updates the mac80211 backport. The removed patches are already integrated in the upstream version. The 131-Revert-mac80211-aes-cmac-switch-to-shash-CMAC-driver.patch patch was manually adapted to the changes in kernel 5.7. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Update to version 5.6.8-1Hauke Mehrtens2020-05-2138-1419/+58
| | | | | | | | This updates the mac80211 backport. The removed patches are already integrated in the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Update to version 5.5.19Hauke Mehrtens2020-05-2142-2895/+369
| | | | | | | | This updates the mac80211 backport. The removed patches are already integrated in the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Update to version 5.4.36-1Hauke Mehrtens2020-05-2117-198/+50
| | | | | | | | | This updates the mac80211 backport to the latest minor version. The removed patch was a backport from the upstream kernel which is now integrated. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: kmod-ptp-qoriq: Package kernel object fileJeffery To2020-05-201-2/+2
| | | | | | | This updates the package to contain the kernel object (.ko) file instead of the plain object (.o) file. Signed-off-by: Jeffery To <jeffery.to@gmail.com>
* bcm63xx-cfe: fix build with CONFIG_AUTOREMOVEÁlvaro Fernández Rojas2020-05-201-6/+7
| | | | | | | | | | | When CONFIG_AUTOREMOVE is enabled, CFE binaries are removed before the image creation. Install CFE binaries to kernel directory and let autoremove clean the files in PKG_BUILD_DIR. Also drop unneeded tar cmd/options. Fixes: dcee4eaa4214 ("bcm63xx-cfe: add package with CFE RAM binaries") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: smp: add NAND supportÁlvaro Fernández Rojas2020-05-181-1/+1
| | | | | | NAND controller is present on BCM6328, BCM6362, BCM6368 and BCM63268. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx-cfe: add package with CFE RAM binariesÁlvaro Fernández Rojas2020-05-181-0/+42
| | | | | | | CFE RAM is a second stage bootloader which is usually loaded by CFE ROM (first stage bootloader) from a JFFS2 partition stored on the NAND. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: drop outdated kernel version switches for local codeAdrian Schmutzler2020-05-1715-174/+0
| | | | | | | | This drops kernel version switches for versions not supported by OpenWrt master at the moment. This only adjusts local code, but doesn't touch patches to existing external packages. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mac80211: replace backticks by $(...)Adrian Schmutzler2020-05-132-2/+2
| | | | | | This replaces deprecated backticks by more versatile $(...) syntax. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ltq-vdsl-fw: replace backticks by $(...)Adrian Schmutzler2020-05-131-3/+3
| | | | | | This replaces deprecated backticks by more versatile $(...) syntax. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mac80211: distance config: allow "auto" as a valueAli MJ Al-Nasrawy2020-05-091-1/+2
| | | | | | | | | The user can now enable the ACK timeout estimation algorithm (dynack) for drivers that support it. It is also expected that the distance config accepts the same values as: $ iw phyX set distance XXX Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
* mac80211: more wifi reconf related fixesJohn Crispin2020-05-041-18/+24
| | | | | | | | | | | * uci state was not getting reset properly during teardown * AP+STA co-exist state was not flushed properly upon channel switch * remove a debug logger call * properly teardown supplicant instances when they get disabled * add md5 config support for supplicant * don't call wpa_supplicant_prepare_interface twice Signed-off-by: John Crispin <john@phrozen.org>
* ath10k-ct: update to version 2020-04-29Petr Štetiar2020-04-301-3/+3
| | | | | | | | | | | | | | | | Pulls in workaround for TX rate code firmware bug which might as well help track it down via different printk()s and thus possibly provide more clue for proper fix. Firmware currently sends wrong (0xff) TX rate code which causes WARN_ONCE, so the workaround just changes this bogus value (0xff) into 0. For 5.4 it also pulls in tx-queue-wake throttling patch "ath10k: Restart xmit queues below low-water mark", which should improve performance with high number of concurrent TCP streams. Ref: https://github.com/greearb/ath10k-ct/pull/129 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: hwmon: add Analog Devices AD741x supportDavid Bauer2020-04-291-0/+14
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 15:47:16 +0000