aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/apm821xx/sata
Commit message (Collapse)AuthorAgeFilesLines
* apm821xx: clean up target/subtarget featuresRui Salvaterra2020-11-251-1/+1
| | | | | | | | Move features common to all subtargets to the parent target. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> [split patch to make it target-specific, adjust commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: move CONFIG_F2FS_CHECK_FS to generic kernel configHauke Mehrtens2020-10-111-1/+0
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Move CONFIG_F2FS_FS_SECURITY to generic kernel configHauke Mehrtens2020-10-111-1/+0
| | | | | | | Move the CONFIG_F2FS_FS_SECURITY kernel configuration option to the generic kernel configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Remove 2FS_FS_XATTR and F2FS_STAT_FS symbols from target configsHauke Mehrtens2020-10-111-1/+0
| | | | | | | This config option was moved to the generic kernel configuration. Fixes: ab1bd576562b ("kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: clean up XATTR config symbolsPaul Spooren2020-10-091-1/+0
| | | | | | | | | | | | | Extended attributes are required for overlayfs and have hence been long ago enabled for jffs2, but should be enabled unconditionally for all other filesystems which may potentially serve as overlayfs' upper directory. Previously it was inconsistently added in multiple targets. Add symbols to generic kernel config and remove all *_XATTR symbols from target configs. Signed-off-by: Paul Spooren <mail@aparcar.org> [keep things as they are for squashfs, improve commit message] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-201-1/+1
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* apm821xx: set DEVICE_TYPE to "nas" for sata subtargetAdrian Schmutzler2020-06-031-0/+1
| | | | | | | | | | | | | | | | Since DEVICE_TYPE cannot be set per device, just set DEVICE_TYPE to "nas" for the entire subtarget, which only contains this single device. Note that while this looks like a cosmetic change in combination with the previous patches, this particular patch actually changes the packages for the device. Suggested-by: Christian Lamparter <chunkeey@gmail.com> Cc: Christian Lamparter <chunkeey@gmail.com> Cc: Sungbo Eo <mans0n@gorani.run> Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* apm821xx: add drivetemp sensor for the WD MyBook SeriesChristian Lamparter2020-03-221-1/+1
| | | | | | | | | This patch adds the hwmon-drivetemp to the device. It also adds device-tree bindings. This can be useful to automate external fans which can be controlled for example by either an unused sata-port or by the usb-power regulator. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: sata: boot-part feature integrationChristian Lamparter2019-01-011-1/+1
| | | | | | | | | | | | This patch adds the boot-part feature to the apm82181 sata target. This makes it possible to configure the boot partition size with the generic CONFIG_TARGET_KERNEL_PARTSIZE symbol. Please note: For people using custom images: Just like with CONFIG_TARGET_ROOTFS_PARTSIZE changing the value can cause sysupgrade to repartition the device! Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add linux 4.19 apm821xx patchesChristian Lamparter2018-12-271-1/+0
| | | | | | | | | | This patch updates the apm821xx target to use the 4.19 kernel. 4.19 ships with all the crypto4xx driver patches. Furthermore, the DW-DMA fix for the SATA controller has been backported from 4.20 and integrated. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: sata: set rootfs-part feature flagChristian Lamparter2018-12-271-1/+1
| | | | | | | | The rootfs-part feature flag ensures that CONFIG_ROOTFS_PART_SIZE symbol will be present at all times. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-161-1/+1
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* apm821xx: clean up gpio-hogsChristian Lamparter2018-07-301-0/+2
| | | | | | | | | | | convert the usb and both sata port power related gpio-hogs to what they really are: fixed-regulators. The ethernet phy-reset gpio-hog is replaced by a proper upstream (4.15+) reset-gpios property in the mdio-node. So this will work eventually. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: build squashfs-rootfs images for the MBLChristian Lamparter2018-07-302-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for squashfs as the root filesystem. advantages: - migrate from a existing -ext4 installation and back with the sysupgrade utility - existing partition layout will not be lost during switch - slightly smaller image size as compared to the -ext4 image. disadvantages: - needs f2fs + tools. This is because fstools rootdisk.c decides based on the partition size (currently root partitions > 100 MiB) f2fs is used as the rootfs_data filesystem. - rootfs_data is placed into the rootfs partition after the squashfs. This makes it difficult for tools that expect a /dev/sda${X} device. It also makes it difficult for data recovery tools as they might not expect to find a embedded partition or will be slightly confused. ... or will not support f2fs. For people with existing build configurations: make sure to include mkf2fs and f2fsck packages into the image. Otherwise the new -squashfs image will only boot from the ram-overlay. Note: All overlay data (configurations/all installed packages/...) will be placed in inside the rootfs partition (i.e. /dev/sda2) just after the squashfs image. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MyBook Live convert to DT PHYChristian Lamparter2017-12-141-0/+1
| | | | | | Changes MyBook Live to use DT PHY probing and the broadcom phy driver. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-1/+1
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* apm821xx: replace recovery image for the MBL with initramfsChristian Lamparter2016-10-132-6/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch "images: bump default rootfs size to 256 MB" a1f83bad606411a561e8e60110c71232b1a28aa2 caused a crash during boot for the recovery images. This is because both variants of the MyBook Live only have 256MB of RAM and for the recovery option, the ext4 rootfs was simply stored in the RAMDISK. This patch replaces recovery image for the MBL with an initramfs kernel. In order to boot the initramfs (for recovery or development): 0. copy the initramfs and device tree into tftp's server directory # cp *-initramfs-kernel.bin to /tftp-server/mbl.bin # cp *-ext4-kernel.dtb to /tftp-server/fdt.bin 1. Connect the MyBook Live (Duo) serial port. (Warning! Use a 3.3v level shifter). 2. Hit Enter during u-boot and insert these three lines: # setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1; # tftp ${kernel_addr_r} mbl.bin; tftp ${fdt_addr_r} fdt.bin # run addtty addmisc; bootm ${kernel_addr_r} - ${fdt_addr_r} Where 192.168.1.254 is your TFTP server. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: backport generic HDD led-triggers for WNDR4700 and MBLChristian Lamparter2016-09-081-0/+1
| | | | | | | This patch backports the new generic HDD/SDD led-trigger from 4.8-rc1. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* tools: bring back genext2fs for apm821xxFelix Fietkau2016-07-231-4/+0
| | | | | | | | This reverts commit 8c68c104eaba65273280c7a4727fbb10ab10f5af. It is used for apm821xx, which needs ext2 (not ext4) images for some devices. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* apm821xx: add missing default profiles for subtargetsFelix Fietkau2016-07-221-0/+18
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* apm821xx: add support for the Western Digital MyBook Live SeriesChristian Lamparter2016-07-222-0/+57
Hardware Highlights: This patch adds support for Western Digital MyBook Live Series: CPU: AMCC PowerPC UNKNOWN (PVR=12c41c83) at 800 MHz (PLB=200, OPB=100, EBC=100 MHz) 32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory Board: Apollo-3G - APM82181 Board, 1*SATA DRAM: 256 MB (2x NT5TU64M16GG-AC) FLASH: 512 kB (SST 39VF040) Ethernet: 1xRGMII - 1 Gbit - Broadcom PHY BCM54610 WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The MyBook Live Duo additionally features a 1x USB 2.0 host port and can support a second hard-drive. This target produces two images for a target. 1. ext4 image The extracted/raw image can be directly installed on the internal HDD via "dd if=img.ext4 of=/dev/sdX". This can either be done in place with the stock MyBook Live firmware via ssh. Or by removing the HDD and writing the image with a different PC. The the compressed images are useful for sysupgrade. 2. recovery.tar image for TFTP and Serial. extract the recovery.tar to a TFTP server directory. On the MyBook Live (Duo) serial port - Hit Enter during u-boot and insert: # setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1; run net_self Where 192.168.1.254 is your TFTP server. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>