aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/files/arch/mips/ath79/dev-eth.h
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: drop targetAdrian Schmutzler2020-08-301-55/+0
| | | | | | | | | | This target has been mostly replaced by ath79 and won't be included in the upcoming release anymore. Finally put it to rest. This also removes all references in packages, tools, etc. as well as the uboot-ar71xx and vsc73x5-ucode packages. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: add support for Fritz!Box 4020David Bauer2018-05-071-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!Box 4020 WiFi-router. SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz RAM: Winbond W971GG6KB-25 FLASH: Macronix MX25L12835F WiFi: QCA9561 b/g/n 3x3 450Mbit/s USB: 1x USB 2.0 IN: WPS button, WiFi button OUT: Power LED green, Internet LED green, WLAN LED green, LAN LED green, INFO LED green, INFO LED red UART: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (LAN + WAN) - WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs Not working: - USB port Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. After transfer is complete you need to powercycle the device to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: QCA956X: add missing registerHenryk Heisig2017-01-261-0/+1
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x"John Crispin2016-03-231-2/+1
| | | | | | | | | | | | The default delays RXD 3. RDV 3, TXD 0, TXE 0 doesn't seem to work for some boards. These boards depend on the preset values of u-boot which may differ. This reverts commit f2d4bb96b62512caa161dcc2867c91692fb16a38. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49071
* ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955xJohn Crispin2016-03-161-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some u-boot versions for QCA955x change the delays based on the link speed during boot. This usually breaks the support of other linkspeeds when OpenWrt is booted. It also conflicts with the at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own values in QCA955X_GMAC_REG_ETH_CFG. The default RGMII values from the Atheros u-boot are currently used to preset the existing mach files. These may have to be adjusted for boards using different values but which are not currently set them explicitely in OpenWrt. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Christian Beier <cb@shoutrlabs.com> Cc: Chris R Blake <chrisrblake93@gmail.com> Cc: Benjamin Berg <benjamin@sipsolutions.net> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> Cc: Matthias Schiffer <mschiffer@universe-factory.net> Cc: Dirk Neukirchen <dirkneukirchen@web.de> Cc: Christian Mehlis <christian@m3hlis.de> Cc: Luka Perkov <luka@openwrt.org> Cc: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 49029
* ar71xx: add a helper function to set RXDV/RXD of ETH_CFG on AR934xFelix Fietkau2015-04-201-0/+1
| | | | | | | | | | | | | | | The ETH_RXDV_DELAY (17:16) and ETH_RXD_DELAY (15:14) are currently not cleared by the function ath79_setup_ar934x_eth_cfg. Clearing these in the ath79_setup_ar934x_eth_cfg may cause problems on some hardware because they rely on the preset value by the bootloader. Instead another function is introduced which also works on ETH_CFG on AR934x. It can be used to safely clear and set ETH_RXDV_DELAY and ETH_RXD_DELAY on machines which require special settings. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 45523
* ar71xx: add a helper function for setting up ETH_CFG register on QCA955xGabor Juhos2014-07-131-0/+1
| | | | | | | | | Signed-off-by: Jon Suphammer <jon@suphammer.net> Patchwork: http://patchwork.openwrt.org/patch/5839/ [juhosg: fix coding style] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 41623
* ar71xx: make ag71xx_mdio_platform_data visibleGabor Juhos2013-12-171-0/+2
| | | | | | | | | | | This enables us to modify the ag71xx_mdio_platform_data from within the board support files. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4613/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39126
* ar71xx: rename ath79_parse_mac_addr to ath79_parse_ascii_macGabor Juhos2013-09-201-1/+1
| | | | | | | | | Rename the function and extend it in order to make it usable from board setup code. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38085
* ar71xx: add a helper function for setting up ETH_CFG register on AR934xGabor Juhos2012-10-171-0/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 33817
* ar71xx: add a helper function for setting up PHY4 swapping on ar933xFelix Fietkau2012-06-061-0/+2
| | | | SVN-Revision: 32092
* ar71xx: merge files-3.2 to filesGabor Juhos2012-02-101-0/+46
SVN-Revision: 30405
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-19 02:55:20 +0000