aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x/config-4.14
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: remove support for kernel 4.14Adrian Schmutzler2020-04-061-489/+0
| | | | | | | | | | | This target has been on kernel 4.19 for several months [1] and already uses kernel 5.4 as testing kernel. Therefore, it should not be necessary to keep support for kernel 4.14 as well. [1] 2a82e0e1ca0f ("ipq806x: switch to 4.19 kernel version") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/nbg6817]
* ipq806x: remove unsupported hw-crypto qce driverEneas U de Queiroz2019-09-291-9/+0
| | | | | | | | | | | | | | | | | | The following symbols, selected by the qce driver were removed: CONFIG_CRYPTO_CBC CONFIG_CRYPTO_CTR CONFIG_CRYPTO_DES CONFIG_CRYPTO_DEV_QCE CONFIG_CRYPTO_ECB CONFIG_CRYPTO_NULL CONFIG_CRYPTO_SEQIV CONFIG_CRYPTO_XTS CONFIG_CRYPTO_GF128MUL was removed as well, since it is only needed by some cipher modes (LRW, GCM), none of which are selected, and it is packaged as a module. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* kernel: bump 4.14 to 4.14.77Koen Vandeputte2018-10-191-0/+1
| | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch New symbol for arm targets: - HARDEN_BRANCH_PREDICTOR Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: Limit NR_CPUS to 2Rosen Penev2018-06-071-1/+1
| | | | | | | | | | ipq806x is all dual core processors. ipq807x is quad core. Removes this from dmesg: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq806x: cleanup kernel configRam Chandra Jangir2018-05-221-14/+8
| | | | | | | | | | Disable MSM8960, MSM8974 and APQ8084 - since these are different SoC's than IPQ806x Removed unrequired serial configs - since ipq806x uses SERIAL_MSM only Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: add kernel 4.14 supportRam Chandra Jangir2018-05-221-0/+502
- Rebased the patches for 4.14 - Dropped spi-qup and 0027, 0028, 0029 clk patches since it's already included in upstream. Tested on IPQ AP148 Board: 1) NOR boot and NAND boot 2) Tested USB and PCIe interfaces 3) WDOG test 4) cpu frequency scaling 5) ethernet, 2G and 5G WiFi 6) ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>