| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Enable the XRX200 PMAC, GSWIP DSA tag and GSIP DSA drivers in the 5.4
kernel config. Update the existing vr9_*.dts{,i} to use the new
Ethernet and switch drivers. Drop the swconfig package from the xrx200
target because swconfig doesn't manage DSA based switches.
The new /etc/config/network format for the DSA driver is not compatible
with the old (swconfig) based one. Show a message during sysupgrade
notifying users about this change and asking them to start with a fresh
config (or forcefully update and then migrate the config manually).
Failsafe mode can now automatically bring up the first lan interface
based on board.json including DSA based setups. Drop
05_set_preinit_iface_lantiq from the xRX200 sub-target as this is not
needed anymore. For now we are keeping it for the ase, xway and
xway_legacy until there's some confirmation that it can be dropped from
there as well.
While here, some boards also receive minor fixups:
- Use LAN1 as LAN1 (according to a photo this port can also be
configured as WAN) on the Buffalo WBMR-300HPD. This makes it easier to
read the port mapping because otherwise we would have LAN{2,3,4} and
WAN (which was the case for the non-DSA version previously).
- vr9_avm_fritz3390.dts: move the "gpio" comment from port 0 and 1 to
their corresponding PHYs
- vr9_tplink_vr200.dtsi: move the "gpio" comment from port 0 to PHY 0
- vr9_tplink_tdw89x0.dtsi: move the "gpio" comment from port 0 to PHY 0
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Tested-by: Notupus <notpp46@googlemail.com> # TD-W9980/DM200/FRITZ 7430
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TDT VR2020
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TP-Link TD-W8980B
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on ZyXEL P-2812HNU-F1
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 7490
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 3490
Tested-by: @jospezial <jospezial@gmx.de> # tested on VGV7510KW22 (o2 Box 6431)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.
Fix execute bit in one case, too.
This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
| |
lantiq.sh is still included in files which do not use it anymore.
Remove the includes.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
| |
Drop the target specific detection function in favour of the generic
one provided by base-files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
|
| |
Remove the former used board name from the device model property and
use the model name as it is.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
|
|
|
|
|
| |
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
| |
It is only used there
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
| |
|
|
|
|
|
|
|
|
| |
So far the network in failsafe is setup only for one board. Use the
eth0 interface as lan interface for all boards for now.
If a board has its lan interface(s) on another eth, a special
handling based on the board name can be added.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
|
|
| |
Fix failsafe mode for TD-W8970, register interface for preinit.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 44353
|
| |
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41638
|
| |
|
|
|
|
|
|
|
| |
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36781
|
| |
|
|
| |
SVN-Revision: 34698
|
|
|
WIFI eeprom:
As discussed, it is impossible for nand and spi flash platforms to have the eeprom data available from mtd. I suggested to load the eeprom from user-space. I've looked into regular firmware loading but this is only possible when using modules. I've created a sysfs entry that allows reading and writing the eeprom data to the platform data. After loading the eeprom data I rely on pci-hotplug support to disable the bogus pci device and rescan the bus (with fixups and all). Because hotplug is not available, an init script is created that performs the copy from mtd to platform data. I think it is best to eventually move the sysfs functions to dev_wifi_athxk.c file, this would get rid of the external to the ath9k platform data.
SPI flash:
It seems that the spi-xway driver is not really working. It causes my kernel to crash in all sorts of ways. I added to bitbang SPI to be able to the calibration data mention above.
I've kept the original mtd partitioning that Netgear uses.
Buttons/LED:
Both buttons are working properly. Two leds are not enabled: The red internet led is connected to the pci_gnt1 pin... I can't disable it because then DMA stops working.
The green wifi led is connected to an unknown atheros gpio.
Signed-off-by: Pieter Voorthuijsen <p.voorthuijsen at gmail.com>
SVN-Revision: 31910
|
