aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/octeon/files
Commit message (Collapse)AuthorAgeFilesLines
* octeon: convert mtd-mac-address to nvmem implementationAnsuel Smith2021-07-193-9/+46
| | | | | | | Define nvmem-cells and convert mtd-mac-address to nvmem implementation. The conversion is done with an automated script. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* treewide: convert mtd-mac-address-increment* to generic implementationAnsuel Smith2021-07-191-3/+3
| | | | | | | | | | | | | Rework patch 681-NET-add-mtd-mac-address-support to implement only the function to read the mac-address from mtd. Generalize mtd-mac-address-increment function so it can be applied to any source of of_get_mac_address. Rename any mtd-mac-address-increment to mac-address-increment. Rename any mtd-mac-address-increment-byte to mac-address-increment-byte. This should make simplify the conversion of target to nvmem implementation. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* octeon: add new target and support for Ubiquiti EdgeRouter 6PDan Brown2021-05-171-0/+60
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ubiquiti EdgeRouter 6P is 6 port router with similar specifications as the EdgeRouter 4, support for which was added in commit dd651e54cc5eadba480a56a7d2c18471e560f491 There are five 10/100/1000 Mbps RJ/Copper ports and one 1000 Mbps SFP port. SoC: Octeon Cavium 7130 (Cavium 3) at 1000MHz Memory: 1GiB DDR3 Flash: 2x2M chips with uboots (chainloaded) + 512K eeprom LEDs: 1x for power status (white/blue, controllable) and 6x for ethernet and SFP ports (no control over them) Buttons: 1x Reset Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 USB: 1x USB3.0 on front panel MII: 1x QSGMII from SoC PHY: 1x Vitesse VSC8504 of which 4 ports are used (phys 4-7) 1x Vitesse VSC8514 of which 2 ports are used (phys 8-9) Network port mapping - eth0 on device maps to lan0 and phy5 - eth1 on device maps to lan1 and phy6 - eth2 on device maps to lan2 and phy7 - eth3 on device maps to lan3 and phy8 - eth4 on device maps to lan4 and phy9 - eth5 (SFP) on device maps to lan5 and phy4 What is not working: - There is no port status available before it goes up - SFP have no additional status and presented as no different from eth - Power-over-ethernet (passive) support has not been tested How to flash the firmware: - copy openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin and openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar to USB flash drive that is formatted to vfat/fat32 - connect USB flash drive to EdgeRouter 6P front USB port - connect serial cable using front RJ45 port (115200 baud, 8N1) - connect power to cable to EdgeRouter 6P - connect terminal to the console to see uboot boot process - interrupt boot by pressing button(s) on your keyboard to log in to the uboot - detect usb connected flash drives by typing to the console: usb start - after drive is detected load initramfs+kernel to the memory by typing: fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin - after initramfs+kernel is loaded to the memory load it by typing: bootoctlinux 0 numcores=4 endbootargs mem=0 - boot process should finish and you will be greeted with console after pressing enter - create directory to mount usb flash drive to by typing: mkdir /tmp/sda - mount flash drive to that directory by typing: mount /dev/sda1 /tmp/sda - flash firmware to router internal storage by typing: sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar - device will reboot and after it gets up you will have edgerouter 6p running openwrt Signed-off-by: Dan Brown <danbrown@gmail.com> [reorder/squash patches, move ethernet@0 to DTS, share image setup] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: create shared DTSI for Ubiquiti E300 platformDan Brown2021-05-172-194/+206
| | | | | | | | | EdgeRouter 4 and upcoming EdgeRouter 6P and 12 have similar setup, so create a shared DTSI to prevent duplicate code. Signed-off-by: Dan Brown <danbrown@gmail.com> [reorder/squash commits, add description, move ethernet@0 to DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: add support for Ubiquiti EdgeRouter 4Roman Kuzmitskii2020-11-052-0/+570
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router. It has internal power supply and needs c13 power cord. There are three 10/100/1000 Mbps RJ45/Copper ports and one 1000 Mbps SFP port connected directly to a SoC. SoC: Octeon Cavium 7130 (Cavium 3) Clocked at 1000Mhz Memory: 1 GiB (SK hynix H5TQ4G63CFR-RDC × 2) DDR3, clocked at 533 Mhz (1066Mhz effective) Flash: - mtd: 8 MiB (Macronix MX25L6408EMI-12G) used for uboot/eeprom - emmc: 4 GiB (SanDisk SDIN7DP2-4G) used for kernel+rootfs Leds: 1x for power status (white/blue, controllable) and 4x for ethernet and sfp ports (no control over them) Buttons: 1x Reset (from SOC) Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC) USB: 1x USB3.0 on front panel (from SoC) MII: 1x QSGMII from SoC is used PHY: 1x Vitesse VSC8504 of which 4x ports is used All physical port numbers are properly mapped inside OS and named by lanX instead of ethX. There is also special purpose four(4) loopX ports available. That loopX ports are currently hardcoded by linux kernel and exact use case of them is currently unknown. We leave them to the linux kernel and octeon board defaults. All four (4) physical ports are connected to the same QSGMII. vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used. Phy mapping: - Phy5 is connected to physical eth0 port - Phy6 is connected to physical eth1 port - Phy7 is connected to physical eth2 port - Phy4 is connected to physical eth3 port Why this device needs external dts: - faster boot time since need to initialize less device tree nodes. - to add actual indication with LED about boot/failure/upgrade. i.e. user could know when to enter failsafe mode or if upgrade is done - reset button support so user can reset their device in case off failure - sfp port indication in dmesg with information about sfp module it also indicates when module inserted or removed Octeon quirks: - There is no port status available before it interface brought up - SFP port can not be tied to actual phy due to octeon-ethernet state and currently we can only get reports a about SFP state in dmesg How to flash the firmware: - copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to USB flash drive that is formatted to vfat/fat32 - connect USB flash drive to edgerouter 4 front USB port - connect serial cable using front RJ45 port (115200 baud, 8N1) - connect power to cable to edgerouter 4 - connect terminal to the console to see uboot boot process - interrupt boot by pressing button(s) on your keyboard to log in to the uboot - detect usb connected flash drives by typing to the console: usb start - after drive is detected load initramfs+kernel to the memory by typing: fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin - after initramfs+kernel is loaded to the memory load it by typing: bootoctlinux 0 numcores=4 endbootargs mem=0 - boot process should finish and you will be greeted with console after pressing enter - create directory to mount usb flash drive to by typing: mkdir /tmp/sda - mount flash drive to that directory by typing: mount /dev/sda1 /tmp/sda - flash firmware to router internal storage by typing: sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar - device will reboot and after it gets up you will have edgerouter 4 running openwrt Reviewed-by: Johannes Kimmel <fff@bareminimum.eu> Tested-by: Johannes Kimmel <fff@bareminimum.eu> Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
* octeon: update to 3.14John Crispin2014-08-188-7608/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 42187
* octeon: add support for the octeon mips64 SoCJohn Crispin2013-08-048-0/+7608
This is the SoC used be the ESR Lite made by ubnt.com Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 37684