aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot/uboot-kirkwood/patches/008-nsa325-uboot-generic.patch
blob: 0bb79fa4e55940eb2b8507c3fb5da978cb6b02fe (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 819bd3b..6a2d578 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -59,6 +59,9 @@ config TARGET_NSA310
 config TARGET_NSA310S
	bool "Zyxel NSA310S"

+config TARGET_NSA325
+	bool "Zyxel NSA325 board"
+
 endchoice

 config SYS_SOC
@@ -82,5 +85,6 @@ source "board/Seagate/goflexhome/Kconfig"
 source "board/Seagate/nas220/Kconfig"
 source "board/zyxel/nsa310/Kconfig"
 source "board/zyxel/nsa310s/Kconfig"
+source "board/zyxel/nsa325/Kconfig"

 endif
diff --git a/board/zyxel/nsa325/Kconfig b/board/zyxel/nsa325/Kconfig
new file mode 100644
index 0000000..1fe5ead
--- /dev/null
+++ b/board/zyxel/nsa325/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_NSA325
+
+config SYS_BOARD
+	default "nsa325"
+
+config SYS_VENDOR
+	default "zyxel"
+
+config SYS_CONFIG_NAME
+	default "nsa325"
+
+endif
diff --git a/board/zyxel/nsa325/MAINTAINERS b/board/zyxel/nsa325/MAINTAINERS
new file mode 100644
index 0000000..130b4d9
--- /dev/null
+++ b/board/zyxel/nsa325/MAINTAINERS
@@ -0,0 +1,6 @@
+NSA325 BOARD
+M:	Alberto Bursi <alberto.bursi@outlook.it>
+S:	Maintained
+F:	board/zyxel/nsa325/
+F:	include/configs/nsa325.h
+F:	configs/nsa325_defconfig
diff --git a/board/zyxel/nsa325/Makefile b/board/zyxel/nsa325/Makefile
new file mode 100644
index 0000000..4ee953b
--- /dev/null
+++ b/board/zyxel/nsa325/Makefile
@@ -0,0 +1,13 @@
+#
+# (C) Copyright 2015 bodhi <mibodhi@gmail.com>
+#
+# Based on
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= nsa325.o
+
diff --git a/board/zyxel/nsa325/kwbimage.cfg b/board/zyxel/nsa325/kwbimage.cfg
new file mode 100644
index 0000000..5a27d38
--- /dev/null
+++ b/board/zyxel/nsa325/kwbimage.cfg
@@ -0,0 +1,78 @@
+# Copyright (C) 2015 bodhi <mibodhi@gmail.com>
+#
+# Extracted from Zyxel GPL source for u-boot-1.1.4_NSA325v2
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+#BOOT_FROM	uart
+BOOT_FROM       nand
+NAND_ECC_MODE   default
+NAND_PAGE_SIZE  0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization
+DATA 0xFFD01400 0x4301503E      # DDR Configuration register
+DATA 0xFFD01404 0xB9843000      # DDR Controller Control Low
+DATA 0xFFD01408 0x33137777      # DDR Timing (Low)
+DATA 0xFFD0140C 0x16000C55      # DDR Timing (High)
+DATA 0xFFD01410 0x04000000      # DDR Address Control
+DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
+DATA 0xFFD01418 0x00000000	#  DDR Operation
+DATA 0xFFD0141C 0x00000672	#  DDR Mode
+DATA 0xFFD01420 0x00000004	#  DDR Extended Mode
+DATA 0xFFD01424 0x0000F14F	#  DDR Controller Control High
+DATA 0xFFD01428 0x000D6720	# DDR3 ODT Read Timing
+DATA 0xFFD0147C 0x0000B571	# DDR2 ODT Write Timing
+DATA 0xFFD01504 0x1FFFFFF1      # CS[0]n Size
+DATA 0xFFD01508 0x20000000      # CS[1]n Base address to 512Mb
+DATA 0xFFD0150C 0x1FFFFFF4      # CS[1]n Size 512Mb Window enabled for CS1
+DATA 0xFFD01514 0x00000000      # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000      # CS[3]n Size, window disabled
+DATA 0xFFD01494 0x00120000      #  DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000      #  DDR ODT Control (High)
+DATA 0xFFD0149C 0x0000E803      # CPU ODT Control
+
+DATA 0xFFD015D0 0x00000630
+DATA 0xFFD015D4 0x00000046
+DATA 0xFFD015D8 0x00000008
+DATA 0xFFD015DC 0x00000000
+DATA 0xFFD015E0 0x00000023
+DATA 0xFFD015E4 0x00203C18
+DATA 0xFFD01620 0x00384800
+DATA 0xFFD01480 0x00000001
+DATA 0xFFD20134 0x66666666
+DATA 0xFFD20138 0x00066666
+
+#Disable nsa325 hardware watchdog to allow successful kwbooting
+DATA 0xFFD10100 0x00004000 # set GPIO 14 to high to disable the watchdog
+DATA 0xFFD10104 0xFFFFBFFF # set GPIO 14 to output (to block any other input to it)
+
+# End of Header extension
+DATA 0x0 0x0
+
diff --git a/board/zyxel/nsa325/nsa325.c b/board/zyxel/nsa325/nsa325.c
new file mode 100644
index 0000000..4cd1c0f
--- /dev/null
+++ b/board/zyxel/nsa325/nsa325.c
@@ -0,0 +1,265 @@
+/*
+ * Copyright (C) 2015 bodhi <mibodhi@gmail.com>
+ *
+ * Based on
+ * Copyright (C) 2014  Jason Plum <jplum@archlinuxarm.org>
+ *
+ * Based on nsa320.c originall written by
+ * Copyright (C) 2012  Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.c originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/cpu.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include "nsa325.h"
+#include <asm/arch/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	/*
+	 * default gpio configuration
+	 * There are maximum 64 gpios controlled through 2 sets of registers
+	 * the below configuration configures mainly initial LED status
+	 */
+	mvebu_config_gpio(NSA325_VAL_LOW, NSA325_VAL_HIGH,
+		       NSA325_OE_LOW, NSA325_OE_HIGH);
+
+	/* Multi-Purpose Pins Functionality configuration */
+	/* (all LEDs & power off active high) */
+	u32 kwmpp_config[] = {
+		MPP0_NF_IO2,
+		MPP1_NF_IO3,
+		MPP2_NF_IO4,
+		MPP3_NF_IO5,
+		MPP4_NF_IO6,
+		MPP5_NF_IO7,
+		MPP6_SYSRST_OUTn,
+		MPP7_GPO,
+		MPP8_TW_SDA,		/* PCF8563 RTC chip   */
+		MPP9_TW_SCK,		/* connected to TWSI  */
+		MPP10_UART0_TXD,
+		MPP11_UART0_RXD,
+		MPP12_GPO,		/* HDD2 LED (green)   */
+		MPP13_GPIO,		/* HDD2 LED (red)     */
+		MPP14_GPIO,		/* MCU DATA pin (in)  */
+		MPP15_GPIO,		/* USB LED (green)    */
+		MPP16_GPIO,		/* MCU CLK pin (out)  */
+		MPP17_GPIO,		/* MCU ACT pin (out)  */
+		MPP18_NF_IO0,
+		MPP19_NF_IO1,
+		MPP20_GPIO,
+		MPP21_GPIO,		/* USB power          */
+		MPP22_GPIO,
+		MPP23_GPIO,
+		MPP24_GPIO,
+		MPP25_GPIO,
+		MPP26_GPIO,
+		MPP27_GPIO,
+		MPP28_GPIO,		/* SYS LED (green)    */
+		MPP29_GPIO,		/* SYS LED (orange)   */
+		MPP30_GPIO,
+		MPP31_GPIO,
+		MPP32_GPIO,
+		MPP33_GPIO,
+		MPP34_GPIO,
+		MPP35_GPIO,
+		MPP36_GPIO,		/* reset button       */
+		MPP37_GPIO,		/* copy button        */
+		MPP38_GPIO,		/* VID B0             */
+		MPP39_GPIO,		/* COPY LED (green)   */
+		MPP40_GPIO,		/* COPY LED (red)     */
+		MPP41_GPIO,		/* HDD1 LED (green)   */
+		MPP42_GPIO,		/* HDD1 LED (red)     */
+		MPP43_GPIO,		/* HTP pin            */
+		MPP44_GPIO,		/* buzzer             */
+		MPP45_GPIO,		/* VID B1             */
+		MPP46_GPIO,		/* power button       */
+		MPP47_GPIO,		/* HDD2 power         */
+		MPP48_GPIO,		/* power off          */
+		0
+	};
+	kirkwood_mpp_conf(kwmpp_config, NULL);
+	return 0;
+}
+
+int board_init(void)
+{
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	/* This disables the hardware watchdog in the mcu on this board. */
+	kw_gpio_set_valid(14, 1);
+	kw_gpio_direction_output(14, 0);
+	kw_gpio_set_value(14, 1);
+
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1318 PHY */
+void reset_phy(void)
+{
+	u16 reg;
+	u16 devadr;
+	char *name = "egiga0";
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/* command to read PHY dev address */
+	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+		printf("Err..%s could not read PHY dev address\n",
+			__FUNCTION__);
+		return;
+	}
+
+	/* Set RGMII delay */
+	miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_MAC_CTRL_PG);
+	miiphy_read(name, devadr, MV88E1318_MAC_CTRL_REG, &reg);
+	reg |= (MV88E1318_RGMII_RXTM_CTRL | MV88E1318_RGMII_TXTM_CTRL);
+	miiphy_write(name, devadr, MV88E1318_MAC_CTRL_REG, reg);
+	miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
+
+	/* reset the phy */
+	miiphy_reset(name, devadr);
+
+	/* The ZyXEL NSA325 uses the 88E1310S Alaska (interface identical to 88E1318) */
+	/* and has an MCU attached to the LED[2] via tristate interrupt */
+	reg = 0;
+
+	/* switch to LED register page */
+	miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_LED_PG);
+	/* read out LED polarity register */
+	miiphy_read(name, devadr, MV88E1318_LED_POL_REG, &reg);
+	/* clear 4, set 5 - LED2 low, tri-state */
+	reg &= ~(MV88E1318_LED2_4);
+	reg |= (MV88E1318_LED2_5);
+	/* write back LED polarity register */
+	miiphy_write(name, devadr, MV88E1318_LED_POL_REG, reg);
+	/* jump back to page 0, per the PHY chip documenation. */
+	miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
+
+	/* Set the phy back to auto-negotiation mode. Onboard mcu sets it as 10Mbits/s on poweroff for WoL function */
+	miiphy_write(name, devadr, 0x4, 0x1e1);
+	miiphy_write(name, devadr, 0x9, 0x300);
+	/* Downshift */
+	miiphy_write(name, devadr, 0x10, 0x3860);
+	miiphy_write(name, devadr, 0x0, 0x9140);
+
+	printf("MV88E1318 PHY initialized on %s\n", name);
+
+}
+#endif /* CONFIG_RESET_PHY_R */
+
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void show_boot_progress(int val)
+{
+	struct kwgpio_registers *gpio0 = (struct kwgpio_registers *)MVEBU_GPIO0_BASE;
+	u32 dout0 = readl(&gpio0->dout);
+	u32 blen0 = readl(&gpio0->blink_en);
+
+	struct kwgpio_registers *gpio1 = (struct kwgpio_registers *)MVEBU_GPIO1_BASE;
+	u32 dout1 = readl(&gpio1->dout);
+	u32 blen1 = readl(&gpio1->blink_en);
+
+	switch (val) {
+	case BOOTSTAGE_ID_DECOMP_IMAGE:
+		writel(blen0 & ~(SYS_GREEN_LED | SYS_ORANGE_LED), &gpio0->blink_en);
+		writel((dout0 & ~SYS_GREEN_LED) | SYS_ORANGE_LED, &gpio0->dout);
+		break;
+	case BOOTSTAGE_ID_RUN_OS:
+		writel(dout0 & ~SYS_ORANGE_LED, &gpio0->dout);
+		writel(blen0 | SYS_GREEN_LED, &gpio0->blink_en);
+		break;
+	case BOOTSTAGE_ID_NET_START:
+		writel(dout1 & ~COPY_RED_LED, &gpio1->dout);
+		writel((blen1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->blink_en);
+		break;
+	case BOOTSTAGE_ID_NET_LOADED:
+		writel(blen1 & ~(COPY_RED_LED | COPY_GREEN_LED), &gpio1->blink_en);
+		writel((dout1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->dout);
+		break;
+	case -BOOTSTAGE_ID_NET_NETLOOP_OK:
+	case -BOOTSTAGE_ID_NET_LOADED:
+		writel(dout1 & ~COPY_GREEN_LED, &gpio1->dout);
+		writel((blen1 & ~COPY_GREEN_LED) | COPY_RED_LED, &gpio1->blink_en);
+		break;
+	default:
+		if (val < 0) {
+			/* error */
+			printf("Error occured, error code = %d\n", -val);
+			writel(dout0 & ~SYS_GREEN_LED, &gpio0->dout);
+			writel(blen0 | SYS_ORANGE_LED, &gpio0->blink_en);
+		}
+		break;
+	}
+}
+#endif
+
+#if defined(CONFIG_KIRKWOOD_GPIO)
+/* Return GPIO button status */
+/*
+un-pressed:
+ gpio-36 (Reset Button ) in hi (act lo) - IRQ edge (clear )
+ gpio-37 (Copy Button  ) in hi (act lo) - IRQ edge (clear )
+ gpio-46 (Power Button ) in lo (act hi) - IRQ edge (clear )
+pressed
+ gpio-36 (Reset Button ) in lo (act hi) - IRQ edge (clear )
+ gpio-37 (Copy Button  ) in lo (act hi) - IRQ edge (clear )
+ gpio-46 (Power Button ) in hi (act lo) - IRQ edge (clear )
+*/
+
+static int
+do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	if (strcmp(argv[1], "power") == 0) {
+			kw_gpio_set_valid(BTN_POWER, GPIO_INPUT_OK);
+			kw_gpio_direction_input(BTN_POWER);
+			return !kw_gpio_get_value(BTN_POWER);
+	}
+	else if (strcmp(argv[1], "reset") == 0)
+		return kw_gpio_get_value(BTN_RESET);
+	else if (strcmp(argv[1], "copy") == 0)
+		return kw_gpio_get_value(BTN_COPY);
+	else
+		return -1;
+}
+
+
+U_BOOT_CMD(button, 2, 0, do_read_button,
+	   "Return GPIO button status 0=off 1=on",
+	   "- button power|reset|copy: test buttons states\n"
+);
+
+#endif
+
diff --git a/board/zyxel/nsa325/nsa325.h b/board/zyxel/nsa325/nsa325.h
new file mode 100644
index 0000000..996653e
--- /dev/null
+++ b/board/zyxel/nsa325/nsa325.h
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2014  Jason Plum <jplum@archlinuxarm.org>
+ *
+ * Based on nsa320.h originall written by
+ * Copyright (C) 2012  Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.h originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __NSA325_H
+#define __NSA325_H
+
+/* low GPIO's */
+#define HDD2_GREEN_LED		(1 << 12)
+#define HDD2_RED_LED		(1 << 13)
+#define USB_GREEN_LED		(1 << 15)
+#define USB_POWER		(1 << 21)
+#define SYS_GREEN_LED		(1 << 28)
+#define SYS_ORANGE_LED		(1 << 29)
+
+#define PIN_USB_GREEN_LED	15
+#define PIN_USB_POWER		21
+
+#define NSA325_OE_LOW		(~(HDD2_GREEN_LED | HDD2_RED_LED | \
+				   USB_GREEN_LED | USB_POWER | \
+				   SYS_GREEN_LED | SYS_ORANGE_LED))
+#define NSA325_VAL_LOW		(SYS_GREEN_LED | USB_POWER)
+
+/* high GPIO's */
+#define COPY_GREEN_LED		(1 << 7)
+#define COPY_RED_LED		(1 << 8)
+#define HDD1_GREEN_LED		(1 << 9)
+#define HDD1_RED_LED		(1 << 10)
+#define HDD2_POWER          (1 << 15)
+#define WATCHDOG_SIGNAL     (1 << 14)
+
+#define NSA325_OE_HIGH		(~(COPY_GREEN_LED | COPY_RED_LED | \
+				   HDD1_GREEN_LED | HDD1_RED_LED | HDD2_POWER | WATCHDOG_SIGNAL ))
+#define NSA325_VAL_HIGH		(WATCHDOG_SIGNAL | HDD2_POWER)
+
+/* PHY related */
+#define MV88E1318_PGADR_REG		22
+#define MV88E1318_MAC_CTRL_PG	2
+#define MV88E1318_MAC_CTRL_REG	21
+#define MV88E1318_RGMII_TXTM_CTRL	(1 << 4)
+#define MV88E1318_RGMII_RXTM_CTRL	(1 << 5)
+#define MV88E1318_LED_PG        3
+#define MV88E1318_LED_POL_REG	17
+#define MV88E1318_LED2_4	    (1 << 4)
+#define MV88E1318_LED2_5	    (1 << 5)
+
+#define BTN_POWER				46
+#define BTN_RESET				36
+#define BTN_COPY				37
+
+#endif /* __NSA325_H */
diff --git a/configs/nsa325_defconfig b/configs/nsa325_defconfig
new file mode 100644
index 0000000..48e09cc
--- /dev/null
+++ b/configs/nsa325_defconfig
@@ -0,0 +1,22 @@
+CONFIG_ARM=y
+CONFIG_KIRKWOOD=y
+CONFIG_TARGET_NSA325=y
+CONFIG_IDENT_STRING="\nZyXEL NSA325 2-Bay Power Media Server"
+CONFIG_BOOTDELAY=3
+CONFIG_SYS_PROMPT="NSA325> "
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_SYS_NS16550=y
+CONFIG_CMD_FDT=y
+CONFIG_OF_LIBFDT=y
+CONFIG_CMD_SETEXPR=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_USB=y
+CONFIG_USB=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_EFI_PARTITION=y
+CONFIG_CMD_UBI=y
+CONFIG_USB_STORAGE=y
diff --git a/include/configs/nsa325.h b/include/configs/nsa325.h
new file mode 100644
index 0000000..e5a8e2a
--- /dev/null
+++ b/include/configs/nsa325.h
@@ -0,0 +1,148 @@
+/*
+ * (C) Copyright 2016 bodhi <mibodhi@gmail.com>
+ *
+ * Based on
+ * Copyright (C) 2014 Jason Plum <jplum@archlinuxarm.org>
+ * Based on
+ * Copyright (C) 2012  Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.h originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_NSA325_H
+#define _CONFIG_NSA325_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131	1	/* CPU Core subversion */
+#define CONFIG_KIRKWOOD		1	/* SOC Family Name */
+#define CONFIG_KW88F6281	1	/* SOC Name */
+
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
+
+/*
+ * Misc Configuration Options
+ */
+#define CONFIG_SHOW_BOOT_PROGRESS 1	/* boot progess display (LED's) */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_DATE
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_PREBOOT
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/*
+ *  Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND		1
+#define CONFIG_ENV_SECT_SIZE		0x20000		/* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE		1		/* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE			0x20000		/* 128k */
+#define CONFIG_ENV_ADDR			0xc0000
+#define CONFIG_ENV_OFFSET		0xc0000	/* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND \
+	"ubi part ubi; " \
+	"ubi read 0x800000 kernel; " \
+	"bootm 0x800000"
+
+#define CONFIG_MTDPARTS \
+	"mtdparts=orion_nand:" \
+	"0x0c0000(uboot)," \
+	"0x80000(uboot_env)," \
+	"0x7ec0000(ubi)\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console=console=ttyS0,115200\0"	\
+	"mtdids=nand0=orion_nand\0"		\
+	"mtdparts="CONFIG_MTDPARTS		\
+	"bootargs_root=\0"
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE_PORTS		{1, 0}	/* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR		0x1
+#define CONFIG_PHY_GIGE
+#define CONFIG_NETCONSOLE
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * SATA Driver configuration
+ */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
+#define CONFIG_SYS_ATA_IDE1_OFFSET      MV_SATA_PORT1_OFFSET
+#endif /* CONFIG_MVSATA_IDE */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_JFFS2
+#define CONFIG_JFFS2_NAND
+#define CONFIG_JFFS2_LZO
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
+/*
+ *  Date Time
+ */
+#ifdef CONFIG_CMD_DATE
+#define CONFIG_RTC_MV
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_DNS
+#endif /* CONFIG_CMD_DATE */
+
+#define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */
+
+#endif /* _CONFIG_NSA325_H */