path: root/package/network/utils/iw/patches/001-nl80211_h_sync.patch

--- a/nl80211.h
+++ b/nl80211.h
@@ -11,7 +11,7 @@
  * Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
  * Copyright 2008 Colin McCabe <colin@cozybit.com>
  * Copyright 2015-2017	Intel Deutschland GmbH
- * Copyright (C) 2018-2019 Intel Corporation
+ * Copyright (C) 2018-2020 Intel Corporation
  *
  * Permission to use, copy, modify, and/or distribute this software for any
  * purpose with or without fee is hereby granted, provided that the above
@@ -249,6 +249,45 @@
  */
 
 /**
+ * DOC: VLAN offload support for setting group keys and binding STAs to VLANs
+ *
+ * By setting @NL80211_EXT_FEATURE_VLAN_OFFLOAD flag drivers can indicate they
+ * support offloading VLAN functionality in a manner where the driver exposes a
+ * single netdev that uses VLAN tagged frames and separate VLAN-specific netdevs
+ * can then be added using RTM_NEWLINK/IFLA_VLAN_ID similarly to the Ethernet
+ * case. Frames received from stations that are not assigned to any VLAN are
+ * delivered on the main netdev and frames to such stations can be sent through
+ * that main netdev.
+ *
+ * %NL80211_CMD_NEW_KEY (for group keys), %NL80211_CMD_NEW_STATION, and
+ * %NL80211_CMD_SET_STATION will optionally specify vlan_id using
+ * %NL80211_ATTR_VLAN_ID.
+ */
+
+/**
+ * DOC: TID configuration
+ *
+ * TID config support can be checked in the %NL80211_ATTR_TID_CONFIG
+ * attribute given in wiphy capabilities.
+ *
+ * The necessary configuration parameters are mentioned in
+ * &enum nl80211_tid_config_attr and it will be passed to the
+ * %NL80211_CMD_SET_TID_CONFIG command in %NL80211_ATTR_TID_CONFIG.
+ *
+ * If the configuration needs to be applied for specific peer then the MAC
+ * address of the peer needs to be passed in %NL80211_ATTR_MAC, otherwise the
+ * configuration will be applied for all the connected peers in the vif except
+ * any peers that have peer specific configuration for the TID by default; if
+ * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer specific values
+ * will be overwritten.
+ *
+ * All this configuration is valid only for STA's current connection
+ * i.e. the configuration will be reset to default when the STA connects back
+ * after disconnection/roaming, and this configuration will be cleared when
+ * the interface goes down.
+ */
+
+/**
  * enum nl80211_commands - supported nl80211 commands
  *
  * @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -257,13 +296,14 @@
  *	to get a list of all present wiphys.
  * @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
  *	%NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
- *	%NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ (and the
- *	attributes determining the channel width; this is used for setting
- *	monitor mode channel),  %NL80211_ATTR_WIPHY_RETRY_SHORT,
- *	%NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
- *	and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
- *	However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
- *	instead, the support here is for backward compatibility only.
+ *	%NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ,
+ *	%NL80211_ATTR_WIPHY_FREQ_OFFSET (and the attributes determining the
+ *	channel width; this is used for setting monitor mode channel),
+ *	%NL80211_ATTR_WIPHY_RETRY_SHORT, %NL80211_ATTR_WIPHY_RETRY_LONG,
+ *	%NL80211_ATTR_WIPHY_FRAG_THRESHOLD, and/or
+ *	%NL80211_ATTR_WIPHY_RTS_THRESHOLD.  However, for setting the channel,
+ *	see %NL80211_CMD_SET_CHANNEL instead, the support here is for backward
+ *	compatibility only.
  * @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
  *	or rename notification. Has attributes %NL80211_ATTR_WIPHY and
  *	%NL80211_ATTR_WIPHY_NAME.
@@ -312,7 +352,8 @@
  *	%NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT,
  *	%NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS.
  *	The channel to use can be set on the interface or be given using the
- *	%NL80211_ATTR_WIPHY_FREQ and the attributes determining channel width.
+ *	%NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_WIPHY_FREQ_OFFSET, and the
+ *	attributes determining channel width.
  * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
  * @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
  * @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
@@ -497,11 +538,12 @@
  *	interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and
  *	BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
  *	the SSID (mainly for association, but is included in authentication
- *	request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ is used
- *	to specify the frequence of the channel in MHz. %NL80211_ATTR_AUTH_TYPE
- *	is used to specify the authentication type. %NL80211_ATTR_IE is used to
- *	define IEs (VendorSpecificInfo, but also including RSN IE and FT IEs)
- *	to be added to the frame.
+ *	request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ +
+ *	%NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequence of the
+ *	channel in MHz. %NL80211_ATTR_AUTH_TYPE is used to specify the
+ *	authentication type. %NL80211_ATTR_IE is used to define IEs
+ *	(VendorSpecificInfo, but also including RSN IE and FT IEs) to be added
+ *	to the frame.
  *	When used as an event, this reports reception of an Authentication
  *	frame in station and IBSS modes when the local MLME processed the
  *	frame, i.e., it was for the local STA and was received in correct
@@ -556,8 +598,9 @@
  *	requests to connect to a specified network but without separating
  *	auth and assoc steps. For this, you need to specify the SSID in a
  *	%NL80211_ATTR_SSID attribute, and can optionally specify the association
- *	IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP,
- *	%NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
+ *	IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE,
+ *	%NL80211_ATTR_USE_MFP, %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ,
+ *	%NL80211_ATTR_WIPHY_FREQ_OFFSET, %NL80211_ATTR_CONTROL_PORT,
  *	%NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
  *	%NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
  *	%NL80211_ATTR_CONTROL_PORT_OVER_NL80211, %NL80211_ATTR_MAC_HINT, and
@@ -571,6 +614,14 @@
  *	set of BSSID,frequency parameters is used (i.e., either the enforcing
  *	%NL80211_ATTR_MAC,%NL80211_ATTR_WIPHY_FREQ or the less strict
  *	%NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT).
+ *	Driver shall not modify the IEs specified through %NL80211_ATTR_IE if
+ *	%NL80211_ATTR_MAC is included. However, if %NL80211_ATTR_MAC_HINT is
+ *	included, these IEs through %NL80211_ATTR_IE are specified by the user
+ *	space based on the best possible BSS selected. Thus, if the driver ends
+ *	up selecting a different BSS, it can modify these IEs accordingly (e.g.
+ *	userspace asks the driver to perform PMKSA caching with BSS1 and the
+ *	driver ends up selecting BSS2 with different PMKSA cache entry; RSNIE
+ *	has to get updated with the apt PMKID).
  *	%NL80211_ATTR_PREV_BSSID can be used to request a reassociation within
  *	the ESS in case the device is already associated and an association with
  *	a different BSS is desired.
@@ -640,6 +691,10 @@
  *	four bytes for vendor frames including the OUI. The registration
  *	cannot be dropped, but is removed automatically when the netlink
  *	socket is closed. Multiple registrations can be made.
+ *	The %NL80211_ATTR_RECEIVE_MULTICAST flag attribute can be given if
+ *	%NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS is available, in which
+ *	case the registration can also be modified to include/exclude the
+ *	flag, rather than requiring unregistration to change it.
  * @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
  *	backward compatibility
  * @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
@@ -739,7 +794,7 @@
  *	various triggers. These triggers can be configured through this
  *	command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
  *	more background information, see
- *	http://wireless.kernel.org/en/users/Documentation/WoWLAN.
+ *	https://wireless.wiki.kernel.org/en/users/Documentation/WoWLAN.
  *	The @NL80211_CMD_SET_WOWLAN command can also be used as a notification
  *	from the driver reporting the wakeup reason. In this case, the
  *	@NL80211_ATTR_WOWLAN_TRIGGERS attribute will contain the reason
@@ -1101,6 +1156,20 @@
  *	peer MAC address and %NL80211_ATTR_FRAME is used to specify the frame
  *	content. The frame is ethernet data.
  *
+ * @NL80211_CMD_SET_TID_CONFIG: Data frame TID specific configuration
+ *	is passed using %NL80211_ATTR_TID_CONFIG attribute.
+ *
+ * @NL80211_CMD_UNPROT_BEACON: Unprotected or incorrectly protected Beacon
+ *	frame. This event is used to indicate that a received Beacon frame was
+ *	dropped because it did not include a valid MME MIC while beacon
+ *	protection was enabled (BIGTK configured in station mode).
+ *
+ * @NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS: Report TX status of a control
+ *	port frame transmitted with %NL80211_CMD_CONTROL_PORT_FRAME.
+ *	%NL80211_ATTR_COOKIE identifies the TX command and %NL80211_ATTR_FRAME
+ *	includes the contents of the frame. %NL80211_ATTR_ACK flag is included
+ *	if the recipient acknowledged the frame.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -1325,6 +1394,12 @@ enum nl80211_commands {
 
 	NL80211_CMD_PROBE_MESH_LINK,
 
+	NL80211_CMD_SET_TID_CONFIG,
+
+	NL80211_CMD_UNPROT_BEACON,
+
+	NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -1370,7 +1445,8 @@ enum nl80211_commands {
  *	of &enum nl80211_chan_width, describing the channel width. See the
  *	documentation of the enum for more information.
  * @NL80211_ATTR_CENTER_FREQ1: Center frequency of the first part of the
- *	channel, used for anything but 20 MHz bandwidth
+ *	channel, used for anything but 20 MHz bandwidth. In S1G this is the
+ *	operating channel center frequency.
  * @NL80211_ATTR_CENTER_FREQ2: Center frequency of the second part of the
  *	channel, used only for 80+80 MHz bandwidth
  * @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
@@ -1580,7 +1656,8 @@ enum nl80211_commands {
  *	flag is included, then control port frames are sent over NL80211 instead
  *	using %CMD_CONTROL_PORT_FRAME.  If control port routing over NL80211 is
  *	to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER
- *	flag.
+ *	flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth
+ *	frames are not forwared over the control port.
  *
  * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
  *	We recommend using nested, driver-specific attributes within this.
@@ -2373,6 +2450,64 @@ enum nl80211_commands {
  *	the allowed channel bandwidth configurations. (u8 attribute)
  *	Defined by IEEE P802.11ay/D4.0 section 9.4.2.251, Table 13.
  *
+ * @NL80211_ATTR_VLAN_ID: VLAN ID (1..4094) for the station and VLAN group key
+ *	(u16).
+ *
+ * @NL80211_ATTR_HE_BSS_COLOR: nested attribute for BSS Color Settings.
+ *
+ * @NL80211_ATTR_IFTYPE_AKM_SUITES: nested array attribute, with each entry
+ *	using attributes from &enum nl80211_iftype_akm_attributes. This
+ *	attribute is sent in a response to %NL80211_CMD_GET_WIPHY indicating
+ *	supported AKM suites capability per interface. AKMs advertised in
+ *	%NL80211_ATTR_AKM_SUITES are default capabilities if AKM suites not
+ *	advertised for a specific interface type.
+ *
+ * @NL80211_ATTR_TID_CONFIG: TID specific configuration in a
+ *	nested attribute with &enum nl80211_tid_config_attr sub-attributes;
+ *	on output (in wiphy attributes) it contains only the feature sub-
+ *	attributes.
+ *
+ * @NL80211_ATTR_CONTROL_PORT_NO_PREAUTH: disable preauth frame rx on control
+ *	port in order to forward/receive them as ordinary data frames.
+ *
+ * @NL80211_ATTR_PMK_LIFETIME: Maximum lifetime for PMKSA in seconds (u32,
+ *	dot11RSNAConfigPMKReauthThreshold; 0 is not a valid value).
+ *	An optional parameter configured through %NL80211_CMD_SET_PMKSA.
+ *	Drivers that trigger roaming need to know the lifetime of the
+ *	configured PMKSA for triggering the full vs. PMKSA caching based
+ *	authentication. This timeout helps authentication methods like SAE,
+ *	where PMK gets updated only by going through a full (new SAE)
+ *	authentication instead of getting updated during an association for EAP
+ *	authentication. No new full authentication within the PMK expiry shall
+ *	result in a disassociation at the end of the lifetime.
+ *
+ * @NL80211_ATTR_PMK_REAUTH_THRESHOLD: Reauthentication threshold time, in
+ *	terms of percentage of %NL80211_ATTR_PMK_LIFETIME
+ *	(u8, dot11RSNAConfigPMKReauthThreshold, 1..100). This is an optional
+ *	parameter configured through %NL80211_CMD_SET_PMKSA. Requests the
+ *	driver to trigger a full authentication roam (without PMKSA caching)
+ *	after the reauthentication threshold time, but before the PMK lifetime
+ *	has expired.
+ *
+ *	Authentication methods like SAE need to be able to generate a new PMKSA
+ *	entry without having to force a disconnection after the PMK timeout. If
+ *	no roaming occurs between the reauth threshold and PMK expiration,
+ *	disassociation is still forced.
+ * @NL80211_ATTR_RECEIVE_MULTICAST: multicast flag for the
+ *	%NL80211_CMD_REGISTER_FRAME command, see the description there.
+ * @NL80211_ATTR_WIPHY_FREQ_OFFSET: offset of the associated
+ *	%NL80211_ATTR_WIPHY_FREQ in positive KHz. Only valid when supplied with
+ *	an %NL80211_ATTR_WIPHY_FREQ_OFFSET.
+ * @NL80211_ATTR_CENTER_FREQ1_OFFSET: Center frequency offset in KHz for the
+ *	first channel segment specified in %NL80211_ATTR_CENTER_FREQ1.
+ * @NL80211_ATTR_SCAN_FREQ_KHZ: nested attribute with KHz frequencies
+ *
+ * @NL80211_ATTR_HE_6GHZ_CAPABILITY: HE 6 GHz Band Capability element (from
+ *	association request when used with NL80211_CMD_NEW_STATION).
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
+ *	transmit power to stay within regulatory limits. u32, dBi.
+ *
  * @NUM_NL80211_ATTR: total number of nl80211_attrs available
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
@@ -2835,6 +2970,28 @@ enum nl80211_attrs {
 	NL80211_ATTR_WIPHY_EDMG_CHANNELS,
 	NL80211_ATTR_WIPHY_EDMG_BW_CONFIG,
 
+	NL80211_ATTR_VLAN_ID,
+
+	NL80211_ATTR_HE_BSS_COLOR,
+
+	NL80211_ATTR_IFTYPE_AKM_SUITES,
+
+	NL80211_ATTR_TID_CONFIG,
+
+	NL80211_ATTR_CONTROL_PORT_NO_PREAUTH,
+
+	NL80211_ATTR_PMK_LIFETIME,
+	NL80211_ATTR_PMK_REAUTH_THRESHOLD,
+
+	NL80211_ATTR_RECEIVE_MULTICAST,
+	NL80211_ATTR_WIPHY_FREQ_OFFSET,
+	NL80211_ATTR_CENTER_FREQ1_OFFSET,
+	NL80211_ATTR_SCAN_FREQ_KHZ,
+
+	NL80211_ATTR_HE_6GHZ_CAPABILITY,
+
+	NL80211_ATTR_WIPHY_ANTENNA_GAIN,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -3413,6 +3570,8 @@ enum nl80211_mpath_info {
  *     defined in HE capabilities IE
  * @NL80211_BAND_IFTYPE_ATTR_MAX: highest band HE capability attribute currently
  *     defined
+ * @NL80211_BAND_IFTYPE_ATTR_HE_6GHZ_CAPA: HE 6GHz band capabilities (__le16),
+ *	given for all 6 GHz band channels
  * @__NL80211_BAND_IFTYPE_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_band_iftype_attr {
@@ -3423,6 +3582,7 @@ enum nl80211_band_iftype_attr {
 	NL80211_BAND_IFTYPE_ATTR_HE_CAP_PHY,
 	NL80211_BAND_IFTYPE_ATTR_HE_CAP_MCS_SET,
 	NL80211_BAND_IFTYPE_ATTR_HE_CAP_PPE,
+	NL80211_BAND_IFTYPE_ATTR_HE_6GHZ_CAPA,
 
 	/* keep last */
 	__NL80211_BAND_IFTYPE_ATTR_AFTER_LAST,
@@ -3554,6 +3714,9 @@ enum nl80211_wmm_rule {
  * @NL80211_FREQUENCY_ATTR_WMM: this channel has wmm limitations.
  *	This is a nested attribute that contains the wmm limitation per AC.
  *	(see &enum nl80211_wmm_rule)
+ * @NL80211_FREQUENCY_ATTR_NO_HE: HE operation is not allowed on this channel
+ *	in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_OFFSET: frequency offset in KHz
  * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
  *	currently defined
  * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
@@ -3583,6 +3746,8 @@ enum nl80211_frequency_attr {
 	NL80211_FREQUENCY_ATTR_NO_20MHZ,
 	NL80211_FREQUENCY_ATTR_NO_10MHZ,
 	NL80211_FREQUENCY_ATTR_WMM,
+	NL80211_FREQUENCY_ATTR_NO_HE,
+	NL80211_FREQUENCY_ATTR_OFFSET,
 
 	/* keep last */
 	__NL80211_FREQUENCY_ATTR_AFTER_LAST,
@@ -3780,6 +3945,7 @@ enum nl80211_sched_scan_match_attr {
  * @NL80211_RRF_NO_HT40PLUS: channels can't be used in HT40+ operation
  * @NL80211_RRF_NO_80MHZ: 80MHz operation not allowed
  * @NL80211_RRF_NO_160MHZ: 160MHz operation not allowed
+ * @NL80211_RRF_NO_HE: HE operation not allowed
  */
 enum nl80211_reg_rule_flags {
 	NL80211_RRF_NO_OFDM		= 1<<0,
@@ -3797,6 +3963,7 @@ enum nl80211_reg_rule_flags {
 	NL80211_RRF_NO_HT40PLUS		= 1<<14,
 	NL80211_RRF_NO_80MHZ		= 1<<15,
 	NL80211_RRF_NO_160MHZ		= 1<<16,
+	NL80211_RRF_NO_HE		= 1<<17,
 };
 
 #define NL80211_RRF_PASSIVE_SCAN	NL80211_RRF_NO_IR
@@ -4351,6 +4518,7 @@ enum nl80211_bss_scan_width {
  * @NL80211_BSS_CHAIN_SIGNAL: per-chain signal strength of last BSS update.
  *	Contains a nested array of signal strength attributes (u8, dBm),
  *	using the nesting index as the antenna number.
+ * @NL80211_BSS_FREQUENCY_OFFSET: frequency offset in KHz
  * @__NL80211_BSS_AFTER_LAST: internal
  * @NL80211_BSS_MAX: highest BSS attribute
  */
@@ -4375,6 +4543,7 @@ enum nl80211_bss {
 	NL80211_BSS_PARENT_TSF,
 	NL80211_BSS_PARENT_BSSID,
 	NL80211_BSS_CHAIN_SIGNAL,
+	NL80211_BSS_FREQUENCY_OFFSET,
 
 	/* keep last */
 	__NL80211_BSS_AFTER_LAST,
@@ -4503,6 +4672,7 @@ enum nl80211_key_default_types {
  *	See &enum nl80211_key_default_types.
  * @NL80211_KEY_MODE: the mode from enum nl80211_key_mode.
  *	Defaults to @NL80211_KEY_RX_TX.
+ * @NL80211_KEY_DEFAULT_BEACON: flag indicating default Beacon frame key
  *
  * @__NL80211_KEY_AFTER_LAST: internal
  * @NL80211_KEY_MAX: highest key attribute
@@ -4518,6 +4688,7 @@ enum nl80211_key_attributes {
 	NL80211_KEY_TYPE,
 	NL80211_KEY_DEFAULT_TYPES,
 	NL80211_KEY_MODE,
+	NL80211_KEY_DEFAULT_BEACON,
 
 	/* keep last */
 	__NL80211_KEY_AFTER_LAST,
@@ -4674,6 +4845,92 @@ enum nl80211_tx_power_setting {
 };
 
 /**
+ * enum nl80211_tid_config - TID config state
+ * @NL80211_TID_CONFIG_ENABLE: Enable config for the TID
+ * @NL80211_TID_CONFIG_DISABLE: Disable config for the TID
+ */
+enum nl80211_tid_config {
+	NL80211_TID_CONFIG_ENABLE,
+	NL80211_TID_CONFIG_DISABLE,
+};
+
+/* enum nl80211_tx_rate_setting - TX rate configuration type
+ * @NL80211_TX_RATE_AUTOMATIC: automatically determine TX rate
+ * @NL80211_TX_RATE_LIMITED: limit the TX rate by the TX rate parameter
+ * @NL80211_TX_RATE_FIXED: fix TX rate to the TX rate parameter
+ */
+enum nl80211_tx_rate_setting {
+	NL80211_TX_RATE_AUTOMATIC,
+	NL80211_TX_RATE_LIMITED,
+	NL80211_TX_RATE_FIXED,
+};
+
+/* enum nl80211_tid_config_attr - TID specific configuration.
+ * @NL80211_TID_CONFIG_ATTR_PAD: pad attribute for 64-bit values
+ * @NL80211_TID_CONFIG_ATTR_VIF_SUPP: a bitmap (u64) of attributes supported
+ *	for per-vif configuration; doesn't list the ones that are generic
+ *	(%NL80211_TID_CONFIG_ATTR_TIDS, %NL80211_TID_CONFIG_ATTR_OVERRIDE).
+ * @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but
+ *	per peer instead.
+ * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribue, if set indicates
+ *	that the new configuration overrides all previous peer
+ *	configurations, otherwise previous peer specific configurations
+ *	should be left untouched.
+ * @NL80211_TID_CONFIG_ATTR_TIDS: a bitmask value of TIDs (bit 0 to 7)
+ *	Its type is u16.
+ * @NL80211_TID_CONFIG_ATTR_NOACK: Configure ack policy for the TID.
+ *	specified in %NL80211_TID_CONFIG_ATTR_TID. see %enum nl80211_tid_config.
+ *	Its type is u8.
+ * @NL80211_TID_CONFIG_ATTR_RETRY_SHORT: Number of retries used with data frame
+ *	transmission, user-space sets this configuration in
+ *	&NL80211_CMD_SET_TID_CONFIG. It is u8 type, min value is 1 and
+ *	the max value is advertised by the driver in this attribute on
+ *	output in wiphy capabilities.
+ * @NL80211_TID_CONFIG_ATTR_RETRY_LONG: Number of retries used with data frame
+ *	transmission, user-space sets this configuration in
+ *	&NL80211_CMD_SET_TID_CONFIG. Its type is u8, min value is 1 and
+ *	the max value is advertised by the driver in this attribute on
+ *	output in wiphy capabilities.
+ * @NL80211_TID_CONFIG_ATTR_AMPDU_CTRL: Enable/Disable MPDU aggregation
+ *	for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS.
+ *	Its type is u8, using the values from &nl80211_tid_config.
+ * @NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL: Enable/Disable RTS_CTS for the TIDs
+ *	specified in %NL80211_TID_CONFIG_ATTR_TIDS. It is u8 type, using
+ *	the values from &nl80211_tid_config.
+ * @NL80211_TID_CONFIG_ATTR_AMSDU_CTRL: Enable/Disable MSDU aggregation
+ *	for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS.
+ *	Its type is u8, using the values from &nl80211_tid_config.
+ * @NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE: This attribute will be useful
+ *	to notfiy the driver that what type of txrate should be used
+ *	for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS. using
+ *	the values form &nl80211_tx_rate_setting.
+ * @NL80211_TID_CONFIG_ATTR_TX_RATE: Data frame TX rate mask should be applied
+ *	with the parameters passed through %NL80211_ATTR_TX_RATES.
+ *	configuration is applied to the data frame for the tid to that connected
+ *	station.
+ */
+enum nl80211_tid_config_attr {
+	__NL80211_TID_CONFIG_ATTR_INVALID,
+	NL80211_TID_CONFIG_ATTR_PAD,
+	NL80211_TID_CONFIG_ATTR_VIF_SUPP,
+	NL80211_TID_CONFIG_ATTR_PEER_SUPP,
+	NL80211_TID_CONFIG_ATTR_OVERRIDE,
+	NL80211_TID_CONFIG_ATTR_TIDS,
+	NL80211_TID_CONFIG_ATTR_NOACK,
+	NL80211_TID_CONFIG_ATTR_RETRY_SHORT,
+	NL80211_TID_CONFIG_ATTR_RETRY_LONG,
+	NL80211_TID_CONFIG_ATTR_AMPDU_CTRL,
+	NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL,
+	NL80211_TID_CONFIG_ATTR_AMSDU_CTRL,
+	NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE,
+	NL80211_TID_CONFIG_ATTR_TX_RATE,
+
+	/* keep last */
+	__NL80211_TID_CONFIG_ATTR_AFTER_LAST,
+	NL80211_TID_CONFIG_ATTR_MAX = __NL80211_TID_CONFIG_ATTR_AFTER_LAST - 1
+};
+
+/**
  * enum nl80211_packet_pattern_attr - packet pattern attribute
  * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
  * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has
@@ -5144,6 +5401,8 @@ enum plink_actions {
 
 #define NL80211_KCK_LEN			16
 #define NL80211_KEK_LEN			16
+#define NL80211_KCK_EXT_LEN		24
+#define NL80211_KEK_EXT_LEN		32
 #define NL80211_REPLAY_CTR_LEN		8
 
 /**
@@ -5152,6 +5411,7 @@ enum plink_actions {
  * @NL80211_REKEY_DATA_KEK: key encryption key (binary)
  * @NL80211_REKEY_DATA_KCK: key confirmation key (binary)
  * @NL80211_REKEY_DATA_REPLAY_CTR: replay counter (binary)
+ * @NL80211_REKEY_DATA_AKM: AKM data (OUI, suite type)
  * @NUM_NL80211_REKEY_DATA: number of rekey attributes (internal)
  * @MAX_NL80211_REKEY_DATA: highest rekey attribute (internal)
  */
@@ -5160,6 +5420,7 @@ enum nl80211_rekey_data {
 	NL80211_REKEY_DATA_KEK,
 	NL80211_REKEY_DATA_KCK,
 	NL80211_REKEY_DATA_REPLAY_CTR,
+	NL80211_REKEY_DATA_AKM,
 
 	/* keep last */
 	NUM_NL80211_REKEY_DATA,
@@ -5484,6 +5745,39 @@ enum nl80211_feature_flags {
  * @NL80211_EXT_FEATURE_SAE_OFFLOAD: Device wants to do SAE authentication in
  *	station mode (SAE password is passed as part of the connect command).
  *
+ * @NL80211_EXT_FEATURE_VLAN_OFFLOAD: The driver supports a single netdev
+ *	with VLAN tagged frames and separate VLAN-specific netdevs added using
+ *	vconfig similarly to the Ethernet case.
+ *
+ * @NL80211_EXT_FEATURE_AQL: The driver supports the Airtime Queue Limit (AQL)
+ *	feature, which prevents bufferbloat by using the expected transmission
+ *	time to limit the amount of data buffered in the hardware.
+ *
+ * @NL80211_EXT_FEATURE_BEACON_PROTECTION: The driver supports Beacon protection
+ *	and can receive key configuration for BIGTK using key indexes 6 and 7.
+ * @NL80211_EXT_FEATURE_BEACON_PROTECTION_CLIENT: The driver supports Beacon
+ *	protection as a client only and cannot transmit protected beacons.
+ *
+ * @NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH: The driver can disable the
+ *	forwarding of preauth frames over the control port. They are then
+ *	handled as ordinary data frames.
+ *
+ * @NL80211_EXT_FEATURE_PROTECTED_TWT: Driver supports protected TWT frames
+ *
+ * @NL80211_EXT_FEATURE_DEL_IBSS_STA: The driver supports removing stations
+ *      in IBSS mode, essentially by dropping their state.
+ *
+ * @NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS: management frame registrations
+ *	are possible for multicast frames and those will be reported properly.
+ *
+ * @NL80211_EXT_FEATURE_SCAN_FREQ_KHZ: This driver supports receiving and
+ *	reporting scan request with %NL80211_ATTR_SCAN_FREQ_KHZ. In order to
+ *	report %NL80211_ATTR_SCAN_FREQ_KHZ, %NL80211_SCAN_FLAG_FREQ_KHZ must be
+ *	included in the scan request.
+ *
+ * @NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_TX_STATUS: The driver
+ *	can report tx status for control port over nl80211 tx operations.
+ *
  * @NUM_NL80211_EXT_FEATURES: number of extended features.
  * @MAX_NL80211_EXT_FEATURES: highest extended feature index.
  */
@@ -5529,6 +5823,16 @@ enum nl80211_ext_feature_index {
 	NL80211_EXT_FEATURE_EXT_KEY_ID,
 	NL80211_EXT_FEATURE_STA_TX_PWR,
 	NL80211_EXT_FEATURE_SAE_OFFLOAD,
+	NL80211_EXT_FEATURE_VLAN_OFFLOAD,
+	NL80211_EXT_FEATURE_AQL,
+	NL80211_EXT_FEATURE_BEACON_PROTECTION,
+	NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH,
+	NL80211_EXT_FEATURE_PROTECTED_TWT,
+	NL80211_EXT_FEATURE_DEL_IBSS_STA,
+	NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS,
+	NL80211_EXT_FEATURE_BEACON_PROTECTION_CLIENT,
+	NL80211_EXT_FEATURE_SCAN_FREQ_KHZ,
+	NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_TX_STATUS,
 
 	/* add new features before the definition below */
 	NUM_NL80211_EXT_FEATURES,
@@ -5640,6 +5944,9 @@ enum nl80211_timeout_reason {
  * @NL80211_SCAN_FLAG_MIN_PREQ_CONTENT: minimize probe request content to
  *	only have supported rates and no additional capabilities (unless
  *	added by userspace explicitly.)
+ * @NL80211_SCAN_FLAG_FREQ_KHZ: report scan results with
+ *	%NL80211_ATTR_SCAN_FREQ_KHZ. This also means
+ *	%NL80211_ATTR_SCAN_FREQUENCIES will not be included.
  */
 enum nl80211_scan_flags {
 	NL80211_SCAN_FLAG_LOW_PRIORITY				= 1<<0,
@@ -5655,6 +5962,7 @@ enum nl80211_scan_flags {
 	NL80211_SCAN_FLAG_HIGH_ACCURACY				= 1<<10,
 	NL80211_SCAN_FLAG_RANDOM_SN				= 1<<11,
 	NL80211_SCAN_FLAG_MIN_PREQ_CONTENT			= 1<<12,
+	NL80211_SCAN_FLAG_FREQ_KHZ				= 1<<13,
 };
 
 /**
@@ -6151,12 +6459,14 @@ enum nl80211_ftm_responder_stats {
  * @NL80211_PREAMBLE_HT: HT preamble
  * @NL80211_PREAMBLE_VHT: VHT preamble
  * @NL80211_PREAMBLE_DMG: DMG preamble
+ * @NL80211_PREAMBLE_HE: HE preamble
  */
 enum nl80211_preamble {
 	NL80211_PREAMBLE_LEGACY,
 	NL80211_PREAMBLE_HT,
 	NL80211_PREAMBLE_VHT,
 	NL80211_PREAMBLE_DMG,
+	NL80211_PREAMBLE_HE,
 };
 
 /**
@@ -6349,6 +6659,10 @@ enum nl80211_peer_measurement_attrs {
  *	is valid)
  * @NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST: u32 attribute indicating
  *	the maximum FTMs per burst (if not present anything is valid)
+ * @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if
+ *	trigger based ranging measurement is supported
+ * @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating
+ *	if non trigger based ranging measurement is supported
  *
  * @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal
  * @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number
@@ -6364,6 +6678,8 @@ enum nl80211_peer_measurement_ftm_capa {
 	NL80211_PMSR_FTM_CAPA_ATTR_BANDWIDTHS,
 	NL80211_PMSR_FTM_CAPA_ATTR_MAX_BURSTS_EXPONENT,
 	NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST,
+	NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED,
+	NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED,
 
 	/* keep last */
 	NUM_NL80211_PMSR_FTM_CAPA_ATTR,
@@ -6393,6 +6709,20 @@ enum nl80211_peer_measurement_ftm_capa {
  * @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI: request LCI data (flag)
  * @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC: request civic location data
  *	(flag)
+ * @NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED: request trigger based ranging
+ *	measurement (flag).
+ *	This attribute and %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED are
+ *	mutually exclusive.
+ *      if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
+ *	%NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
+ *	ranging will be used.
+ * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non trigger based
+ *	ranging measurement (flag)
+ *	This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are
+ *	mutually exclusive.
+ *      if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
+ *	%NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
+ *	ranging will be used.
  *
  * @NUM_NL80211_PMSR_FTM_REQ_ATTR: internal
  * @NL80211_PMSR_FTM_REQ_ATTR_MAX: highest attribute number
@@ -6409,6 +6739,8 @@ enum nl80211_peer_measurement_ftm_req {
 	NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES,
 	NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI,
 	NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC,
+	NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED,
+	NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED,
 
 	/* keep last */
 	NUM_NL80211_PMSR_FTM_REQ_ATTR,
@@ -6548,5 +6880,51 @@ enum nl80211_obss_pd_attributes {
 	NL80211_HE_OBSS_PD_ATTR_MAX = __NL80211_HE_OBSS_PD_ATTR_LAST - 1,
 };
 
+/**
+ * enum nl80211_bss_color_attributes - BSS Color attributes
+ * @__NL80211_HE_BSS_COLOR_ATTR_INVALID: Invalid
+ *
+ * @NL80211_HE_BSS_COLOR_ATTR_COLOR: the current BSS Color.
+ * @NL80211_HE_BSS_COLOR_ATTR_DISABLED: is BSS coloring disabled.
+ * @NL80211_HE_BSS_COLOR_ATTR_PARTIAL: the AID equation to be used..
+ *
+ * @__NL80211_HE_BSS_COLOR_ATTR_LAST: Internal
+ * @NL80211_HE_BSS_COLOR_ATTR_MAX: highest BSS Color attribute.
+ */
+enum nl80211_bss_color_attributes {
+	__NL80211_HE_BSS_COLOR_ATTR_INVALID,
+
+	NL80211_HE_BSS_COLOR_ATTR_COLOR,
+	NL80211_HE_BSS_COLOR_ATTR_DISABLED,
+	NL80211_HE_BSS_COLOR_ATTR_PARTIAL,
+
+	/* keep last */
+	__NL80211_HE_BSS_COLOR_ATTR_LAST,
+	NL80211_HE_BSS_COLOR_ATTR_MAX = __NL80211_HE_BSS_COLOR_ATTR_LAST - 1,
+};
+
+/**
+ * enum nl80211_iftype_akm_attributes - interface type AKM attributes
+ * @__NL80211_IFTYPE_AKM_ATTR_INVALID: Invalid
+ *
+ * @NL80211_IFTYPE_AKM_ATTR_IFTYPES: nested attribute containing a flag
+ *	attribute for each interface type that supports AKM suites specified in
+ *	%NL80211_IFTYPE_AKM_ATTR_SUITES
+ * @NL80211_IFTYPE_AKM_ATTR_SUITES: an array of u32. Used to indicate supported
+ *	AKM suites for the specified interface types.
+ *
+ * @__NL80211_IFTYPE_AKM_ATTR_LAST: Internal
+ * @NL80211_IFTYPE_AKM_ATTR_MAX: highest interface type AKM attribute.
+ */
+enum nl80211_iftype_akm_attributes {
+	__NL80211_IFTYPE_AKM_ATTR_INVALID,
+
+	NL80211_IFTYPE_AKM_ATTR_IFTYPES,
+	NL80211_IFTYPE_AKM_ATTR_SUITES,
+
+	/* keep last */
+	__NL80211_IFTYPE_AKM_ATTR_LAST,
+	NL80211_IFTYPE_AKM_ATTR_MAX = __NL80211_IFTYPE_AKM_ATTR_LAST - 1,
+};
 
 #endif /* __LINUX_NL80211_H */