target/linux/ath79/dts/ar9331_tplink_tl-wr710n-v1.dts


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "ar9331.dtsi"

/ {
	model = "TP-Link TL-WR710N v1";
	compatible = "tplink,tl-wr710n-v1", "qca,ar9331";

	aliases {
		serial0 = &uart;
		led-boot = &led_system;
		led-failsafe = &led_system;
		led-running = &led_system;
		led-upgrade = &led_system;
		label-mac-device = &eth0;
	};

	keys {
		compatible = "gpio-keys";

		reset {
			label = "reset";
			linux,code = <KEY_RESTART>;
			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
			debounce-interval = <60>;
		};
	};

	leds {
		compatible = "gpio-leds";

		led_system: system {
			label = "tl-wr710n:green:system";
			gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
		};
	};

	reg_usb_vbus: regulator {
		compatible = "regulator-fixed";
		regulator-name = "usb_vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
		enable-active-high;
	};
};

&spi {
	status = "okay";
	num-cs = <1>;

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <25000000>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			uboot: partition@0 {
				reg = <0x0 0x20000>;
				label = "u-boot";
				read-only;
			};

			firmware: partition@20000 {
				compatible = "tplink,firmware";
				reg = <0x20000 0x7d0000>;
				label = "firmware";
			};

			art: partition@7f0000 {
				reg = <0x7f0000 0x10000>;
				label = "art";
				read-only;
			};
		};
	};
};

&eth0 {
	status = "okay";

	mtd-mac-address = <&uboot 0x1fc00>;

	gmac-config {
		device = <&gmac>;

		switch-phy-addr-swap = <0>;
		switch-phy-swap = <0>;
	};
};

&eth1 {
	status = "okay";

	mtd-mac-address = <&uboot 0x1fc00>;
	mtd-mac-address-increment = <(-1)>;
};

&gpio {
	status = "okay";
};

&uart {
	status = "okay";
};

&usb {
	dr_mode = "host";
	vbus-supply = <&reg_usb_vbus>;
	status = "okay";
};

&usb_phy {
	status = "okay";
};

&wmac {
	status = "okay";
	mtd-cal-data = <&art 0x1000>;
	mtd-mac-address = <&uboot 0x1fc00>;
};