1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9344.dtsi"
/ {
compatible = "teltonika,rut9xx", "qca,ar9344";
aliases {
serial0 = &uart;
serial1 = &hs_uart;
label-mac-device = ð1;
};
i2c0: i2c {
compatible = "i2c-gpio";
scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
#address-cells = <1>;
#size-cells = <0>;
hwmon@4d {
compatible = "microchip,mcp3221";
reg = <0x4d>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&ref {
clock-frequency = <40000000>;
};
&uart {
status = "okay";
};
&hs_uart {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pmx_uart2>;
rts-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
rs485-rts-active-low;
linux,rs485-enabled-at-boot-time;
};
&spi {
status = "okay";
num-cs = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pmx_spi>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x20000>;
read-only;
};
config: partition@20000 {
label = "config";
reg = <0x20000 0x10000>;
read-only;
};
art: partition@30000 {
label = "art";
reg = <0x30000 0x10000>;
read-only;
};
partition@40000 {
label = "firmware";
reg = <0x40000 0xf30000>;
compatible = "tplink,firmware";
};
partition@f70000 {
label = "event-log";
reg = <0xf70000 0x90000>;
read-only;
};
};
};
microsd@1 {
status = "disabled";
compatible = "mmc-spi-slot";
spi-max-frequency = <25000000>;
reg = <1>;
voltage-ranges = <3200 3400>;
broken-cd;
};
};
&usb {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
port@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
port@1 {
compatible = "usb-a-connector";
reg = <1>;
};
port@3 {
label = "RS-232 serial adapter";
reg = <3>;
};
port@4 {
label = "internal wwan modem";
reg = <4>;
};
};
};
&usb_phy {
status = "okay";
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&config 0x0>;
mtd-mac-address-increment = <2>;
};
&pinmux {
pmx_spi: spi {
// SPI_CS1 on GPIO 3
pinctrl-single,bits = <0x0 0x07000000 0xff000000>;
};
pmx_leds_switch: leds_switch {
// switch port LEDs on GPIO 1, GPIO 13, GPIO 14 and GPIO 22
pinctrl-single,bits = <0x0 0x00002d00 0x0000ff00>,
<0xc 0x002c2b00 0x00ffff00>,
<0x14 0x002a0000 0x00ff0000>;
};
pmx_uart2: uart2 {
// UART1_DTR on GPIO 0, UART1_RD on GPIO 11, UART1_TD on GPIO 18
pinctrl-single,bits = <0x0 0x0 0xff>,
<0x10 0x4f000000 0xff000000>,
<0x3c 0x000b0000 0x00ff0000>;
};
};
|
