blob: ca6d4ec883e0e18138585e5c106e5b955af803df (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca956x.dtsi"
/ {
model = "Phicomm K2T";
compatible = "phicomm,k2t";
aliases {
led-status = &status_red;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
leds {
compatible = "gpio-leds";
status_blue {
label = "phicomm:blue:status";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
default-state = "off";
};
status_red: status_red {
label = "phicomm:red:status";
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
status_yellow {
label = "phicomm:yellow:status";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
default-state = "off";
};
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
reset {
linux,code = <KEY_RESTART>;
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&uart {
status = "okay";
};
&gpio {
status = "okay";
};
&pcie {
status = "okay";
};
&spi {
num-cs = <1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x30000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x030000 0x10000>;
read-only;
};
partition@40000 {
label = "permanent";
reg = <0x040000 0x50000>;
read-only;
};
partition@90000 {
label = "firmware";
reg = <0x090000 0xf60000>;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy-mask = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "sgmii";
qca,ar8327-initvals = <
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
0x10 0x81000080 /* POWER_ON_STRIP */
0x50 0xcc35cc35 /* LED_CTRL0 */
0x54 0xcb37cb37 /* LED_CTRL1 */
0x58 0x00000000 /* LED_CTRL2 */
0x5c 0x00f3cf00 /* LED_CTRL3 */
0x7c 0x0000007e /* PORT0_STATUS */
>;
};
};
ð0 {
status = "okay";
pll-data = <0x03000101 0x00000101 0x00001919>;
phy-mode = "sgmii";
phy-handle = <&phy0>;
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
};
|
