aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/dts/tp9343_tplink_tl-wr940n-v3.dtsi
blob: 5c897b16a099048c7abd0e6e498f5639f8be8ccb (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "tp9343_tplink_tl-wr94x.dtsi"

/ {
	aliases {
		led-boot = &led_system;
		led-failsafe = &led_system;
		led-running = &led_system;
		led-upgrade = &led_system;
	};

	leds {
		compatible = "gpio-leds";

		led_system: system {
			label = "blue:system";
			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
			default-state = "on";
		};

		qss {
			label = "blue:qss";
			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
		};

		wlan {
			label = "blue:wlan";
			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
			linux,default-trigger = "phy0tpt";
		};

		wan_blue {
			label = "blue:wan";
			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
		};

		wan_red {
			label = "red:wan";
			gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
		};

		lan1 {
			label = "blue:lan1";
			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
		};

		lan2 {
			label = "blue:lan2";
			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
		};

		lan3 {
			label = "blue:lan3";
			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
		};

		lan4 {
			label = "blue:lan4";
			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
		};
	};
};

&eth1 {
	mtd-mac-address = <&uboot 0x1fc00>;
	mtd-mac-address-increment = <(-1)>;
};
="n">default-trigger = "usbport"; }; }; keys { compatible = "gpio-keys"; reset { label = "reset"; linux,code = <KEY_RESTART>; gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; debounce-interval = <60>; }; sw1 { label = "sw1"; linux,input-type = <EV_SW>; linux,code = <BTN_0>; gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; debounce-interval = <60>; }; sw2 { label = "sw2"; linux,input-type = <EV_SW>; linux,code = <BTN_1>; gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; debounce-interval = <60>; }; }; reg_usb_vbus: reg_usb_vbus { compatible = "regulator-fixed"; regulator-name = "usb_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio 18 GPIO_ACTIVE_HIGH>; enable-active-high; }; }; &ref { clock-frequency = <25000000>; }; &usb { #address-cells = <1>; #size-cells = <0>; dr_mode = "host"; vbus-supply = <&reg_usb_vbus>; status = "okay"; hub_port: port@1 { reg = <1>; #trigger-source-cells = <0>; }; }; &usb_phy { status = "okay"; }; &spi { status = "okay"; flash@0 { compatible = "jedec,spi-nor"; spi-max-frequency = <50000000>; reg = <0>; partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; uboot: partition@0 { label = "u-boot"; reg = <0x000000 0x020000>; read-only; }; partition@20000 { compatible = "tplink,firmware"; label = "firmware"; reg = <0x020000 0x3d0000>; }; art: partition@3f0000 { label = "art"; reg = <0x3f0000 0x010000>; read-only; }; }; }; }; &eth0 { status = "okay"; mtd-mac-address = <&uboot 0x1fc00>; gmac-config { device = <&gmac>; switch-phy-addr-swap = <0>; switch-phy-swap = <0>; }; }; &eth1 { status = "okay"; compatible = "syscon", "simple-mfd"; }; &wmac { status = "okay"; mtd-cal-data = <&art 0x1000>; mtd-mac-address = <&uboot 0x1fc00>; };