1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
|
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
@@ -6,7 +6,8 @@ configuration settings. The mode settin
the 4 GSBI IOs.
Required properties:
-- compatible: must contain "qcom,gsbi-v1.0.0" for APQ8064/IPQ8064
+- compatible: Should contain "qcom,gsbi-v1.0.0"
+- cell-index: Should contain the GSBI index
- reg: Address range for GSBI registers
- clocks: required clock
- clock-names: must contain "iface" entry
@@ -16,6 +17,8 @@ Required properties:
Optional properties:
- qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference
dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values.
+- syscon-tcsr: indicates phandle of TCSR syscon node. Required if child uses
+ dma.
Required properties if child node exists:
- #address-cells: Must be 1
@@ -39,6 +42,7 @@ Example for APQ8064:
gsbi4@16300000 {
compatible = "qcom,gsbi-v1.0.0";
+ cell-index = <4>;
reg = <0x16300000 0x100>;
clocks = <&gcc GSBI4_H_CLK>;
clock-names = "iface";
@@ -48,6 +52,8 @@ Example for APQ8064:
qcom,mode = <GSBI_PROT_I2C_UART>;
qcom,crci = <GSBI_CRCI_QUP>;
+ syscon-tcsr = <&tcsr>;
+
/* child nodes go under here */
i2c_qup4: i2c@16380000 {
@@ -76,3 +82,9 @@ Example for APQ8064:
};
};
+ tcsr: syscon@1a400000 {
+ compatible = "qcom,apq8064-tcsr", "syscon";
+ reg = <0x1a400000 0x100>;
+ };
+
+
--- a/drivers/soc/qcom/Kconfig
+++ b/drivers/soc/qcom/Kconfig
@@ -4,6 +4,7 @@
config QCOM_GSBI
tristate "QCOM General Serial Bus Interface"
depends on ARCH_QCOM
+ select MFD_SYSCON
help
Say y here to enable GSBI support. The GSBI provides control
functions for connecting the underlying serial UART, SPI, and I2C
--- a/drivers/soc/qcom/qcom_gsbi.c
+++ b/drivers/soc/qcom/qcom_gsbi.c
@@ -18,22 +18,129 @@
#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
#define GSBI_CTRL_REG 0x0000
#define GSBI_PROTOCOL_SHIFT 4
+#define MAX_GSBI 12
+
+#define TCSR_ADM_CRCI_BASE 0x70
+
+struct crci_config {
+ u32 num_rows;
+ const u32 (*array)[MAX_GSBI];
+};
+
+static const u32 crci_ipq8064[][MAX_GSBI] = {
+ {
+ 0x000003, 0x00000c, 0x000030, 0x0000c0,
+ 0x000300, 0x000c00, 0x003000, 0x00c000,
+ 0x030000, 0x0c0000, 0x300000, 0xc00000
+ },
+ {
+ 0x000003, 0x00000c, 0x000030, 0x0000c0,
+ 0x000300, 0x000c00, 0x003000, 0x00c000,
+ 0x030000, 0x0c0000, 0x300000, 0xc00000
+ },
+};
+
+static const struct crci_config config_ipq8064 = {
+ .num_rows = ARRAY_SIZE(crci_ipq8064),
+ .array = crci_ipq8064,
+};
+
+static const unsigned int crci_apq8064[][MAX_GSBI] = {
+ {
+ 0x001800, 0x006000, 0x000030, 0x0000c0,
+ 0x000300, 0x000400, 0x000000, 0x000000,
+ 0x000000, 0x000000, 0x000000, 0x000000
+ },
+ {
+ 0x000000, 0x000000, 0x000000, 0x000000,
+ 0x000000, 0x000020, 0x0000c0, 0x000000,
+ 0x000000, 0x000000, 0x000000, 0x000000
+ },
+};
+
+static const struct crci_config config_apq8064 = {
+ .num_rows = ARRAY_SIZE(crci_apq8064),
+ .array = crci_apq8064,
+};
+
+static const unsigned int crci_msm8960[][MAX_GSBI] = {
+ {
+ 0x000003, 0x00000c, 0x000030, 0x0000c0,
+ 0x000300, 0x000400, 0x000000, 0x000000,
+ 0x000000, 0x000000, 0x000000, 0x000000
+ },
+ {
+ 0x000000, 0x000000, 0x000000, 0x000000,
+ 0x000000, 0x000020, 0x0000c0, 0x000300,
+ 0x001800, 0x006000, 0x000000, 0x000000
+ },
+};
+
+static const struct crci_config config_msm8960 = {
+ .num_rows = ARRAY_SIZE(crci_msm8960),
+ .array = crci_msm8960,
+};
+
+static const unsigned int crci_msm8660[][MAX_GSBI] = {
+ { /* ADM 0 - B */
+ 0x000003, 0x00000c, 0x000030, 0x0000c0,
+ 0x000300, 0x000c00, 0x003000, 0x00c000,
+ 0x030000, 0x0c0000, 0x300000, 0xc00000
+ },
+ { /* ADM 0 - B */
+ 0x000003, 0x00000c, 0x000030, 0x0000c0,
+ 0x000300, 0x000c00, 0x003000, 0x00c000,
+ 0x030000, 0x0c0000, 0x300000, 0xc00000
+ },
+ { /* ADM 1 - A */
+ 0x000003, 0x00000c, 0x000030, 0x0000c0,
+ 0x000300, 0x000c00, 0x003000, 0x00c000,
+ 0x030000, 0x0c0000, 0x300000, 0xc00000
+ },
+ { /* ADM 1 - B */
+ 0x000003, 0x00000c, 0x000030, 0x0000c0,
+ 0x000300, 0x000c00, 0x003000, 0x00c000,
+ 0x030000, 0x0c0000, 0x300000, 0xc00000
+ },
+};
+
+static const struct crci_config config_msm8660 = {
+ .num_rows = ARRAY_SIZE(crci_msm8660),
+ .array = crci_msm8660,
+};
struct gsbi_info {
struct clk *hclk;
u32 mode;
u32 crci;
+ struct regmap *tcsr;
+};
+
+static const struct of_device_id tcsr_dt_match[] = {
+ { .compatible = "qcom,tcsr-ipq8064", .data = &config_ipq8064},
+ { .compatible = "qcom,tcsr-apq8064", .data = &config_apq8064},
+ { .compatible = "qcom,tcsr-msm8960", .data = &config_msm8960},
+ { .compatible = "qcom,tcsr-msm8660", .data = &config_msm8660},
+ { },
};
static int gsbi_probe(struct platform_device *pdev)
{
struct device_node *node = pdev->dev.of_node;
+ struct device_node *tcsr_node;
+ const struct of_device_id *match;
struct resource *res;
void __iomem *base;
struct gsbi_info *gsbi;
+ int i;
+ u32 mask, gsbi_num;
+ const struct crci_config *config = NULL;
gsbi = devm_kzalloc(&pdev->dev, sizeof(*gsbi), GFP_KERNEL);
@@ -45,6 +152,32 @@ static int gsbi_probe(struct platform_de
if (IS_ERR(base))
return PTR_ERR(base);
+ /* get the tcsr node and setup the config and regmap */
+ gsbi->tcsr = syscon_regmap_lookup_by_phandle(node, "syscon-tcsr");
+
+ if (!IS_ERR(gsbi->tcsr)) {
+ tcsr_node = of_parse_phandle(node, "syscon-tcsr", 0);
+ if (tcsr_node) {
+ match = of_match_node(tcsr_dt_match, tcsr_node);
+ if (match)
+ config = match->data;
+ else
+ dev_warn(&pdev->dev, "no matching TCSR\n");
+
+ of_node_put(tcsr_node);
+ }
+ }
+
+ if (of_property_read_u32(node, "cell-index", &gsbi_num)) {
+ dev_err(&pdev->dev, "missing cell-index\n");
+ return -EINVAL;
+ }
+
+ if (gsbi_num < 1 || gsbi_num > MAX_GSBI) {
+ dev_err(&pdev->dev, "invalid cell-index\n");
+ return -EINVAL;
+ }
+
if (of_property_read_u32(node, "qcom,mode", &gsbi->mode)) {
dev_err(&pdev->dev, "missing mode configuration\n");
return -EINVAL;
@@ -64,6 +197,25 @@ static int gsbi_probe(struct platform_de
writel_relaxed((gsbi->mode << GSBI_PROTOCOL_SHIFT) | gsbi->crci,
base + GSBI_CTRL_REG);
+ /*
+ * modify tcsr to reflect mode and ADM CRCI mux
+ * Each gsbi contains a pair of bits, one for RX and one for TX
+ * SPI mode requires both bits cleared, otherwise they are set
+ */
+ if (config) {
+ for (i = 0; i < config->num_rows; i++) {
+ mask = config->array[i][gsbi_num - 1];
+
+ if (gsbi->mode == GSBI_PROT_SPI)
+ regmap_update_bits(gsbi->tcsr,
+ TCSR_ADM_CRCI_BASE + 4 * i, mask, 0);
+ else
+ regmap_update_bits(gsbi->tcsr,
+ TCSR_ADM_CRCI_BASE + 4 * i, mask, mask);
+
+ }
+ }
+
/* make sure the gsbi control write is not reordered */
wmb();
|
