Clean up the driver directory structure by moving all board specific files into the boards sub-structure.

1 files changed, 102 insertions, 0 deletions

diff --git a/boards/addons/gdisp/board_SSD1963_gpio.h b/boards/addons/gdisp/board_SSD1963_gpio.h
new file mode 100644
index 00000000..0b9c0135
--- /dev/null
+++ b/boards/addons/gdisp/board_SSD1963_gpio.h
@@ -0,0 +1,102 @@
+/*
+ * This file is subject to the terms of the GFX License. If a copy of
+ * the license was not distributed with this file, you can obtain one at:
+ *
+ *              http://chibios-gfx.com/license.html
+ */
+
+/**
+ * @file    drivers/gdisp/SSD1963/board_SSD1963_gpio.h
+ * @brief   GDISP Graphic Driver subsystem board interface for the SSD1963 display.
+ */
+
+#ifndef _GDISP_LLD_BOARD_H
+#define _GDISP_LLD_BOARD_H
+
+static const LCD_Parameters	DisplayTimings[] = {
+	// You need one of these array elements per display
+	{
+		480, 272,								// Panel width and height
+		2, 2, 41,								// Horizontal Timings (back porch, front porch, pulse)
+		CALC_PERIOD(480,2,2,41),				// Total Horizontal Period (calculated from above line)
+		2, 2, 10,								// Vertical Timings (back porch, front porch, pulse)
+		CALC_PERIOD(272,2,2,10),				// Total Vertical Period (calculated from above line)
+		CALC_FPR(480,272,2,2,41,2,2,10,60ULL)	// FPR - the 60ULL is the frames per second. Note the ULL!
+	},
+};
+
+// For a multiple display configuration we would put all this in a structure and then
+//	set g->board to that structure.
+
+/**
+ * @brief	The GPIO pin config
+ *
+ * @details	This block of defines tell your driver how you wired your display
+ *			controller to your MCU. Please change them accordingly.
+ */
+#define GDISP_CMD_PORT		GPIOC
+#define GDISP_DATA_PORT		GPIOD
+#define GDISP_CS			0
+#define GDISP_RS			1
+#define GDISP_WR			2
+#define GDISP_RD			3
+
+#define Set_CS		palSetPad(GDISP_CMD_PORT, GDISP_CS);
+#define Clr_CS		palClearPad(GDISP_CMD_PORT, GDISP_CS);
+#define Set_RS		palSetPad(GDISP_CMD_PORT, GDISP_RS);
+#define Clr_RS		palClearPad(GDISP_CMD_PORT, GDISP_RS);
+#define Set_WR		palSetPad(GDISP_CMD_PORT, GDISP_WR);
+#define Clr_WR		palClearPad(GDISP_CMD_PORT, GDISP_WR);
+#define Set_RD		palSetPad(GDISP_CMD_PORT, GDISP_RD);
+#define Clr_RD		palClearPad(GDISP_CMD_PORT, GDISP_RD);
+
+static inline void init_board(GDisplay *g) {
+
+	// As we are not using multiple displays we set g->board to NULL as we don't use it.
+	g->board = 0;
+
+	switch(g->controllerdisplay) {
+	case 0:											// Set up for Display 0
+		IOBus busCMD = {GDISP_CMD_PORT, (1 << GDISP_CS) | (1 << GDISP_RS) | (1 << GDISP_WR) | (1 << GDISP_RD), 0};
+		IOBus busDATA = {GDISP_CMD_PORT, 0xFFFFF, 0};
+		palSetBusMode(&busCMD, PAL_MODE_OUTPUT_PUSHPULL);
+		palSetBusMode(&busDATA, PAL_MODE_OUTPUT_PUSHPULL);
+		break;
+	}
+}
+
+static inline void post_init_board(GDisplay *g) {
+	(void) g;
+}
+
+static inline void setpin_reset(GDisplay *g, bool_t state) {
+	(void) g;
+	(void) state;
+}
+
+static inline void acquire_bus(GDisplay *g) {
+	(void) g;
+	Set_CS;
+}
+
+static inline void release_bus(GDisplay *g) {
+	(void) g;
+	Clr_CS;
+}
+
+static inline void write_index(GDisplay *g, uint16_t index) {
+	(void) g;
+	Set_RS; Clr_RD; Set_WR;
+	palWritePort(GDISP_DATA_PORT, index);
+	Clr_WR;
+}
+
+static inline void write_data(GDisplay *g, uint16_t data) {
+	(void) g;
+	Clr_RS; Clr_RD; Set_WR;
+	palWritePort(GDISP_DATA_PORT, data);
+	Clr_WR;
+}
+
+#endif /* _GDISP_LLD_BOARD_H */
+