Clean up the driver directory structure by moving all board specific files into the boards sub-structure.

1 files changed, 0 insertions, 160 deletions

diff --git a/drivers/gdisp/HX8347D/board_HX8347D_stm32f4discovery.h b/drivers/gdisp/HX8347D/board_HX8347D_stm32f4discovery.h
deleted file mode 100644
index df287477..00000000
--- a/drivers/gdisp/HX8347D/board_HX8347D_stm32f4discovery.h
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/gdisp/HX8347D/board_HX8347D_stm32f4discovery.h
- * @brief   GDISP Graphic Driver subsystem board SPI interface for the HX8347D display.
- */
-
-#ifndef _GDISP_LLD_BOARD_H
-#define _GDISP_LLD_BOARD_H
-
-// For a multiple display configuration we would put all this in a structure and then
-//	set g->board to that structure.
-
-/* Pin assignments */
-#define SET_RST		palSetPad(GPIOB, 8)
-#define CLR_RST		palClearPad(GPIOB, 8)
-#define SET_DATA	palSetPad(GPIOB, 9)
-#define CLR_DATA	palClearPad(GPIOB, 9)
-#define SET_CS		palSetPad(GPIOA, 4)
-#define CLR_CS		palClearPad(GPIOA, 4)
-
-/* PWM configuration structure. We use timer 4 channel 2 (orange LED on board). */
-static const PWMConfig pwmcfg = {
-	1000000,		/* 1 MHz PWM clock frequency. */
-	100,			/* PWM period is 100 cycles. */
-	NULL,
-	{
-		{PWM_OUTPUT_ACTIVE_HIGH, NULL},
-		{PWM_OUTPUT_ACTIVE_HIGH, NULL},
-		{PWM_OUTPUT_ACTIVE_HIGH, NULL},
-		{PWM_OUTPUT_ACTIVE_HIGH, NULL}
-	},
-	0
-};
-
-/*
- * SPI1 configuration structure.
- * Speed 42MHz, CPHA=0, CPOL=0, 8bits frames, MSb transmitted first.
- * The slave select line is the pin 4 on the port GPIOA.
- */
-static const SPIConfig spi1cfg_8bit = {
-	NULL,
-	/* HW dependent part.*/
-	GPIOA,
-	4,
-	0 //SPI_CR1_BR_0
-};
-
-/*
- * SPI1 configuration structure.
- * Speed 42MHz, CPHA=0, CPOL=0, 16bits frames, MSb transmitted first.
- * The slave select line is the pin 4 on the port GPIOA.
- */
-static const SPIConfig spi1cfg_16bit = {
-	NULL,
-	/* HW dependent part.*/
-	GPIOA,
-	4,
-	SPI_CR1_DFF //SPI_CR1_BR_0
-};
-
-static inline void init_board(GDisplay *g) {
-
-	// As we are not using multiple displays we set g->board to NULL as we don't use it.
-	g->board = 0;
-
-	switch(g->controllerdisplay) {
-	case 0:											// Set up for Display 0
-		/* Display backlight control */
-		/* TIM4 is an alternate function 2 (AF2) */
-		pwmStart(&PWMD4, &pwmcfg);
-		palSetPadMode(GPIOD, 13, PAL_MODE_ALTERNATE(2));
-		pwmEnableChannel(&PWMD4, 1, 100);
-
-		palSetPadMode(GPIOB, 8, PAL_MODE_OUTPUT_PUSHPULL|PAL_STM32_OSPEED_HIGHEST);			/* RST    */
-		palSetPadMode(GPIOB, 9, PAL_MODE_OUTPUT_PUSHPULL|PAL_STM32_OSPEED_HIGHEST);			/* RS     */
-		/*
-		 * Initializes the SPI driver 1. The SPI1 signals are routed as follow:
-		 * PB12 - NSS.
-		 * PB13 - SCK.
-		 * PB14 - MISO.
-		 * PB15 - MOSI.
-		 */
-		SET_CS; SET_DATA;
-		spiStart(&SPID1, &spi1cfg_8bit);
-		palSetPadMode(GPIOA, 4, PAL_MODE_OUTPUT_PUSHPULL|PAL_STM32_OSPEED_HIGHEST);			/* NSS.     */
-		palSetPadMode(GPIOA, 5, PAL_MODE_ALTERNATE(5)|PAL_STM32_OSPEED_HIGHEST);			/* SCK.     */
-		palSetPadMode(GPIOA, 6, PAL_MODE_ALTERNATE(5));										/* MISO.    */
-		palSetPadMode(GPIOA, 7, PAL_MODE_ALTERNATE(5)|PAL_STM32_OSPEED_HIGHEST);			/* MOSI.    */
-		break;
-	}
-}
-
-static inline void post_init_board(GDisplay *g) {
-	(void) g;
-}
-
-static inline void setpin_reset(GDisplay *g, bool_t state) {
-	(void) g;
-	if (state) {
-		CLR_RST;
-	} else {
-		SET_RST;
-	}
-}
-
-static inline void set_backlight(GDisplay *g, uint8_t percent) {
-	(void) g;
-	pwmEnableChannel(&PWMD4, 1, percent);
-}
-
-static inline void acquire_bus(GDisplay *g) {
-	(void) g;
-	spiAcquireBus(&SPID1);
-    while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0));		// Safety
-	CLR_CS;
-}
-
-static inline void release_bus(GDisplay *g) {
-	(void) g;
-	SET_CS;
-	spiReleaseBus(&SPID1);
-}
-
-static inline void busmode16(GDisplay *g) {
-	(void) g;
-	spiStart(&SPID1, &spi1cfg_16bit);
-}
-
-static inline void busmode8(GDisplay *g) {
-	(void) g;
-	spiStart(&SPID1, &spi1cfg_8bit);
-}
-
-static inline void write_index(GDisplay *g, uint8_t index) {
-	(void) g;
-    CLR_DATA;
-    SPI1->DR = index;
-    while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0));
-    SET_DATA;
-}
-
-static inline void write_data(GDisplay *g, uint8_t data) {
-	(void) g;
-    SPI1->DR = data;
-    while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0));
-}
-
-static inline void write_ram16(GDisplay *g, uint16_t data) {
-	(void) g;
-    SPI1->DR      = data;
-    while((SPI1->SR & SPI_SR_TXE) == 0);
-}
-
-#endif /* _GDISP_LLD_BOARD_H */