diff options
Diffstat (limited to 'boards/base')
-rw-r--r-- | boards/base/Olimex-STM32-LCD/board.mk | 8 | ||||
-rw-r--r-- | boards/base/Olimex-STM32-LCD/board_ILI9320.h | 101 | ||||
-rw-r--r-- | boards/base/Olimex-STM32-LCD/chibios_board/board.c | 88 | ||||
-rw-r--r-- | boards/base/Olimex-STM32-LCD/chibios_board/board.h | 196 | ||||
-rw-r--r-- | boards/base/Olimex-STM32-LCD/chibios_board/board.mk | 5 | ||||
-rw-r--r-- | boards/base/Olimex-STM32-LCD/ginput_lld_mouse_board.h | 109 | ||||
-rw-r--r-- | boards/base/Olimex-STM32-LCD/ginput_lld_mouse_config.h | 22 | ||||
-rw-r--r-- | boards/base/Olimex-STM32-LCD/readme.txt | 6 |
8 files changed, 535 insertions, 0 deletions
diff --git a/boards/base/Olimex-STM32-LCD/board.mk b/boards/base/Olimex-STM32-LCD/board.mk new file mode 100644 index 00000000..a1e4b935 --- /dev/null +++ b/boards/base/Olimex-STM32-LCD/board.mk @@ -0,0 +1,8 @@ +GFXINC += $(GFXLIB)/boards/base/Olimex-STM32-LCD +GFXSRC += +GFXDEFS += -DGFX_USE_CHIBIOS=TRUE + +include $(GFXLIB)/boards/base/Olimex-STM32-LCD/chibios_board/board.mk +include $(GFXLIB)/drivers/gdisp/ILI9320/gdisp_lld.mk +include $(GFXLIB)/drivers/ginput/touch/MCU/ginput_lld.mk + diff --git a/boards/base/Olimex-STM32-LCD/board_ILI9320.h b/boards/base/Olimex-STM32-LCD/board_ILI9320.h new file mode 100644 index 00000000..fb8c4590 --- /dev/null +++ b/boards/base/Olimex-STM32-LCD/board_ILI9320.h @@ -0,0 +1,101 @@ +/* + * This file is subject to the terms of the GFX License. If a copy of + * the license was not distributed with this file, you can obtain one at: + * + * http://ugfx.org/license.html + */ + +#ifndef GDISP_LLD_BOARD_H +#define GDISP_LLD_BOARD_H + +// For a multiple display configuration we would put all this in a structure and then +// set g->board to that structure. +#define GDISP_REG (*((volatile uint16_t *) 0x60000000)) /* RS = 0 */ +#define GDISP_RAM (*((volatile uint16_t *) 0x60100000)) /* RS = 1 */ + +static inline void init_board(GDisplay *g) { + + // As we are not using multiple displays we set g->board to NULL as we don't use it. + g->board = 0; + + switch(g->controllerdisplay) { + case 0: // Set up for Display 0 + /* FSMC setup for F1 */ + rccEnableAHB(RCC_AHBENR_FSMCEN, 0); + + /* set pin modes */ + IOBus busD = {GPIOD, PAL_WHOLE_PORT, 0}; + IOBus busE = {GPIOE, PAL_WHOLE_PORT, 0}; + palSetBusMode(&busD, PAL_MODE_STM32_ALTERNATE_PUSHPULL); + palSetBusMode(&busE, PAL_MODE_STM32_ALTERNATE_PUSHPULL); + palSetPadMode(GPIOE, GPIOE_TFT_RST, PAL_MODE_OUTPUT_PUSHPULL); + palSetPadMode(GPIOD, GPIOD_TFT_LIGHT, PAL_MODE_OUTPUT_PUSHPULL); + + /* FSMC timing */ + FSMC_Bank1->BTCR[0+1] = (6) | (10 << 8) | (10 << 16); + + /* Bank1 NOR/SRAM control register configuration + * This is actually not needed as already set by default after reset */ + FSMC_Bank1->BTCR[0] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN; + break; + } +} + +static inline void post_init_board(GDisplay *g) { + (void) g; +} + +static inline void setpin_reset(GDisplay *g, bool_t state) { + (void) g; + + if(state) + palClearPad(GPIOE, GPIOE_TFT_RST); + else + palSetPad(GPIOE, GPIOE_TFT_RST); +} + +static inline void set_backlight(GDisplay *g, uint8_t percent) { + (void) g; + + if(percent) + palClearPad(GPIOD, GPIOD_TFT_LIGHT); + else + palSetPad(GPIOD, GPIOD_TFT_LIGHT); +} + +static inline void acquire_bus(GDisplay *g) { + (void) g; +} + +static inline void release_bus(GDisplay *g) { + (void) g; +} + +static inline void write_index(GDisplay *g, uint16_t index) { + (void) g; + + GDISP_REG = index; +} + +static inline void write_data(GDisplay *g, uint16_t data) { + (void) g; + + GDISP_RAM = data; +} + +static inline void setreadmode(GDisplay *g) { + (void) g; +} + +static inline void setwritemode(GDisplay *g) { + (void) g; +} + +static inline uint16_t read_data(GDisplay *g) { + (void) g; + + return GDISP_RAM; +} + +#endif /* GDISP_LLD_BOARD_H */ + diff --git a/boards/base/Olimex-STM32-LCD/chibios_board/board.c b/boards/base/Olimex-STM32-LCD/chibios_board/board.c new file mode 100644 index 00000000..397ed99b --- /dev/null +++ b/boards/base/Olimex-STM32-LCD/chibios_board/board.c @@ -0,0 +1,88 @@ +/*
+ ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#include "ch.h"
+#include "hal.h"
+
+/**
+ * @brief PAL setup.
+ * @details Digital I/O ports static configuration as defined in @p board.h.
+ * This variable is used by the HAL when initializing the PAL driver.
+ */
+#if HAL_USE_PAL || defined(__DOXYGEN__)
+const PALConfig pal_default_config =
+{
+ {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},
+ {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},
+ {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},
+ {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},
+ {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},
+ {VAL_GPIOFODR, VAL_GPIOFCRL, VAL_GPIOFCRH},
+ {VAL_GPIOGODR, VAL_GPIOGCRL, VAL_GPIOGCRH},
+};
+#endif
+
+/*
+ * Early initialization code.
+ * This initialization must be performed just after stack setup and before
+ * any other initialization.
+ */
+void __early_init(void) {
+ stm32_clock_init();
+}
+
+#if HAL_USE_SDC || defined(__DOXYGEN__)
+/**
+ * @brief SDC card detection.
+ */
+bool_t sdc_lld_is_card_inserted(SDCDriver *sdcp) {
+ (void)sdcp;
+
+ return TRUE;
+}
+
+/**
+ * @brief SDC card write protection detection.
+ */
+bool_t sdc_lld_is_write_protected(SDCDriver *sdcp) {
+ (void)sdcp;
+
+ return FALSE;
+}
+#endif /* HAL_USE_SDC */
+
+#if HAL_USE_MMC_SPI
+/* Board-related functions related to the MMC_SPI driver.*/
+bool_t mmc_lld_is_card_inserted(MMCDriver *mmcp) {
+ (void)mmcp;
+
+ return TRUE;
+}
+
+bool_t mmc_lld_is_write_protected(MMCDriver *mmcp) {
+ (void)mmcp;
+
+ return FALSE;
+}
+#endif
+
+/*
+ * Board-specific initialization code.
+ */
+void boardInit(void) {
+
+}
+
diff --git a/boards/base/Olimex-STM32-LCD/chibios_board/board.h b/boards/base/Olimex-STM32-LCD/chibios_board/board.h new file mode 100644 index 00000000..0d510aba --- /dev/null +++ b/boards/base/Olimex-STM32-LCD/chibios_board/board.h @@ -0,0 +1,196 @@ +/*
+ ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Setup for the Olimex STM32-LCD proto board.
+ */
+
+/*
+ * Board identifier.
+ */
+#define BOARD_OLIMEX_STM32_LCD
+#define BOARD_NAME "Olimex STM32-LCD"
+
+/*
+ * Board frequencies.
+ */
+#define STM32_LSECLK 32768
+#define STM32_HSECLK 8000000
+
+/*
+ * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
+ */
+#define STM32F10X_HD
+
+/*
+ * IO pins assignments.
+ */
+#define GPIOA_SPI1NSS 4
+
+#define GPIOB_SPI2NSS 12
+
+#define GPIOA_USB_P 0
+#define GPIOD_USB_DISC 2
+
+#define GPIOE_TFT_RST 2
+#define GPIOD_TFT_LIGHT 13
+#define GPIOC_TFT_YD 0
+#define GPIOC_TFT_YU 1
+#define GPIOC_TFT_XL 2
+#define GPIOC_TFT_XR 3
+
+/*
+ * I/O ports initial setup, this configuration is established soon after reset
+ * in the initialization code.
+ *
+ * The digits have the following meaning:
+ * 0 - Analog input.
+ * 1 - Push Pull output 10MHz.
+ * 2 - Push Pull output 2MHz.
+ * 3 - Push Pull output 50MHz.
+ * 4 - Digital input.
+ * 5 - Open Drain output 10MHz.
+ * 6 - Open Drain output 2MHz.
+ * 7 - Open Drain output 50MHz.
+ * 8 - Digital input with PullUp or PullDown resistor depending on ODR.
+ * 9 - Alternate Push Pull output 10MHz.
+ * A - Alternate Push Pull output 2MHz.
+ * B - Alternate Push Pull output 50MHz.
+ * C - Reserved.
+ * D - Alternate Open Drain output 10MHz.
+ * E - Alternate Open Drain output 2MHz.
+ * F - Alternate Open Drain output 50MHz.
+ * Please refer to the STM32 Reference Manual for details.
+ */
+
+/*
+ * Port A setup.
+ * Everything input with pull-up except:
+ * PA0 - Normal input (USB P).
+ * PA2 - Alternate output (USART2 TX).
+ * PA3 - Normal input (USART2 RX).
+ * PA11 - Normal input (USB DM).
+ * PA12 - Normal input (USB DP).
+ */
+#define VAL_GPIOACRL 0x88884B84 /* PA7...PA0 */
+#define VAL_GPIOACRH 0x88844888 /* PA15...PA8 */
+#define VAL_GPIOAODR 0xFFFFFFFF
+
+/*
+ * Port B setup.
+ * Everything input with pull-up except:
+ */
+#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
+#define VAL_GPIOBCRH 0x88888888 /* PB15...PB8 */
+#define VAL_GPIOBODR 0xFFFFFFFF
+
+/*
+ * Port C setup.
+ * Everything input with pull-up except:
+ * PC0 - Analog Input (TP_YD).
+ * PC1 - Analog Input (TP_YU).
+ * PC2 - Analog Input (TP_XL).
+ * PC3 - Analog Input (TP_XR).
+ * PC8 - Alternate PP 50M (SD_D0).
+ * PC9 - Alternate PP 50M (SD_D1).
+ * PC10 - Alternate PP 50M (SD_D2).
+ * PC11 - Alternate PP 50M (SD_D3).
+ * PC12 - Alternate PP 50M (SD_CLK).
+ * PC14 - Normal input (XTAL).
+ * PC15 - Normal input (XTAL).
+ */
+#define VAL_GPIOCCRL 0x88880000 /* PC7...PC0 */
+#define VAL_GPIOCCRH 0x448BBBBB /* PC15...PC8 */
+#define VAL_GPIOCODR 0xFFFFFFFF
+
+/*
+ * Port D setup.
+ * Everything input with pull-up except:
+ * PD2 - Alternate PP 50M (SD_CMD)
+ * PD0 - Alternate PP 50M (FSMC_D2)
+ * PD1 - Alternate PP 50M (FSMC_D3)
+ * PD4 - Alternate PP 50M (TFT_RD)
+ * PD5 - Alternate PP 50M (TFT_WR)
+ * PD7 - Alternate PP 50M (TFT_CS)
+ * PD8 - Alternate PP 50M (FSMC_D13)
+ * PD9 - Alternate PP 50M (FSMC_D14)
+ * PD10 - Alternate PP 50M (FSMC_D15)
+ * PD14 - Alternate PP 50M (FSMC_D0)
+ * PD15 - Alternate PP 50M (FSMC_D1)
+ */
+#define VAL_GPIODCRL 0xBBBB8BBB /* PD7...PD0 */
+#define VAL_GPIODCRH 0xBB388BBB /* PD15...PD8 */
+#define VAL_GPIODODR 0xFFFFFFFF
+
+/*
+ * Port E setup.
+ * Everything input with pull-up except:
+ * PE2 - Digital Output (TFT_RST)
+ * PE3 - Alternate PP 50M (TFT_RS)
+ * PE7 - Alternate PP 50M (FSMC_D4)
+ * PE8 - Alternate PP 50M (FSMC_D5)
+ * PE9 - Alternate PP 50M (FSMC_D6)
+ * PE10 - Alternate PP 50M (FSMC_D7)
+ * PE11 - Alternate PP 50M (FSMC_D8)
+ * PE12 - Alternate PP 50M (FSMC_D9)
+ * PE13 - Alternate PP 50M (FSMC_D10)
+ * PE14 - Alternate PP 50M (FSMC_D11)
+ * PE15 - Alternate PP 50M (FSMC_D12)
+ */
+#define VAL_GPIOECRL 0xB888B388 /* PE7...PE0 */
+#define VAL_GPIOECRH 0xBBBBBBBB /* PE15...PE8 */
+#define VAL_GPIOEODR 0xFFFFFFFF
+
+/*
+ * Port F setup.
+ * Everything input with pull-up expect:
+ */
+#define VAL_GPIOFCRL 0x88888888 /* PF7...PF0 */
+#define VAL_GPIOFCRH 0x88888888 /* PF15...PF8 */
+#define VAL_GPIOFODR 0xFFFFFFFF
+
+/*
+ * Port G setup.
+ * Everything input with pull-up expect:
+ */
+#define VAL_GPIOGCRL 0x88888888 /* PG7...PG0 */
+#define VAL_GPIOGCRH 0x88888888 /* PG15...PG8 */
+#define VAL_GPIOGODR 0xFFFFFFFF
+
+/*
+ * USB bus activation macro, required by the USB driver.
+ */
+#define usb_lld_connect_bus(usbp) palClearPad(GPIOD, GPIOD_USB_DISC)
+
+/*
+ * USB bus de-activation macro, required by the USB driver.
+ */
+#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOD, GPIOD_USB_DISC)
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+ void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+#endif /* _BOARD_H_ */
diff --git a/boards/base/Olimex-STM32-LCD/chibios_board/board.mk b/boards/base/Olimex-STM32-LCD/chibios_board/board.mk new file mode 100644 index 00000000..c1cc061d --- /dev/null +++ b/boards/base/Olimex-STM32-LCD/chibios_board/board.mk @@ -0,0 +1,5 @@ +# List of all the board related files.
+BOARDSRC = ${CHIBIOS}/boards/OLIMEX_STM32_LCD/board.c
+
+# Required include directories
+BOARDINC = ${CHIBIOS}/boards/OLIMEX_STM32_LCD
diff --git a/boards/base/Olimex-STM32-LCD/ginput_lld_mouse_board.h b/boards/base/Olimex-STM32-LCD/ginput_lld_mouse_board.h new file mode 100644 index 00000000..7a383c60 --- /dev/null +++ b/boards/base/Olimex-STM32-LCD/ginput_lld_mouse_board.h @@ -0,0 +1,109 @@ +/* + * This file is subject to the terms of the GFX License. If a copy of + * the license was not distributed with this file, you can obtain one at: + * + * http://ugfx.org/license.html + */ + +#ifndef _GINPUT_LLD_MOUSE_BOARD_H +#define _GINPUT_LLD_MOUSE_BOARD_H + +#define ADC_NUM_CHANNELS 2 +#define ADC_BUF_DEPTH 1 + +static const ADCConversionGroup adc_y_config = { + FALSE, + ADC_NUM_CHANNELS, + NULL, + NULL, + 0, 0, + 0, 0, + ADC_SQR1_NUM_CH(ADC_NUM_CHANNELS), + 0, + ADC_SQR3_SQ2_N(ADC_CHANNEL_IN12) | ADC_SQR3_SQ1_N(ADC_CHANNEL_IN13) +}; + +static const ADCConversionGroup adc_x_config = { + FALSE, + ADC_NUM_CHANNELS, + NULL, + NULL, + 0, 0, + 0, 0, + ADC_SQR1_NUM_CH(ADC_NUM_CHANNELS), + 0, + ADC_SQR3_SQ2_N(ADC_CHANNEL_IN10) | ADC_SQR3_SQ1_N(ADC_CHANNEL_IN11) +}; + +static inline void init_board(void) { + adcStart(&ADCD1, NULL); +} + +static inline bool_t getpin_pressed(void) { + palSetPadMode(GPIOC, 0, PAL_MODE_INPUT_PULLDOWN); + palSetPadMode(GPIOC, 1, PAL_MODE_INPUT); + palSetPadMode(GPIOC, 2, PAL_MODE_INPUT); + palSetPadMode(GPIOC, 3, PAL_MODE_OUTPUT_PUSHPULL); + palSetPad(GPIOC, 3); + + return palReadPad(GPIOC, 0); +} + +static inline void aquire_bus(void) { + +} + +static inline void release_bus(void) { + +} + +static inline uint16_t read_x_value(void) { + uint16_t val1, val2; + adcsample_t samples[ADC_NUM_CHANNELS * ADC_BUF_DEPTH]; + + palSetPadMode(GPIOC, 0, PAL_MODE_INPUT_ANALOG); + palSetPadMode(GPIOC, 1, PAL_MODE_INPUT_ANALOG); + palSetPadMode(GPIOC, 2, PAL_MODE_OUTPUT_PUSHPULL); + palSetPadMode(GPIOC, 3, PAL_MODE_OUTPUT_PUSHPULL); + + palSetPad(GPIOC, 2); + palClearPad(GPIOC, 3); + gfxSleepMilliseconds(1); + adcConvert(&ADCD1, &adc_x_config, samples, ADC_BUF_DEPTH); + val1 = ((samples[0] + samples[1])/2); + + palClearPad(GPIOC, 2); + palSetPad(GPIOC, 3); + gfxSleepMilliseconds(1); + adcConvert(&ADCD1, &adc_x_config, samples, ADC_BUF_DEPTH); + val2 = ((samples[0] + samples[1])/2); + + return ((val1+((1<<12)-val2))/4); +} + +static inline uint16_t read_y_value(void) { + uint16_t val1, val2; + adcsample_t samples[ADC_NUM_CHANNELS * ADC_BUF_DEPTH]; + + palSetPadMode(GPIOC, 2, PAL_MODE_INPUT_ANALOG); + palSetPadMode(GPIOC, 3, PAL_MODE_INPUT_ANALOG); + palSetPadMode(GPIOC, 0, PAL_MODE_OUTPUT_PUSHPULL); + palSetPadMode(GPIOC, 1, PAL_MODE_OUTPUT_PUSHPULL); + + palSetPad(GPIOC, 1); + palClearPad(GPIOC, 0); + gfxSleepMilliseconds(1); + adcConvert(&ADCD1, &adc_y_config, samples, ADC_BUF_DEPTH); + val1 = ((samples[0] + samples[1])/2); + + palClearPad(GPIOC, 1); + palSetPad(GPIOC, 0); + gfxSleepMilliseconds(1); + adcConvert(&ADCD1, &adc_y_config, samples, ADC_BUF_DEPTH); + val2 = ((samples[0] + samples[1])/2); + + return ((val1+((1<<12)-val2))/4); +} + +#endif /* _GINPUT_LLD_MOUSE_BOARD_H */ + diff --git a/boards/base/Olimex-STM32-LCD/ginput_lld_mouse_config.h b/boards/base/Olimex-STM32-LCD/ginput_lld_mouse_config.h new file mode 100644 index 00000000..bba2cdd1 --- /dev/null +++ b/boards/base/Olimex-STM32-LCD/ginput_lld_mouse_config.h @@ -0,0 +1,22 @@ +/* + * This file is subject to the terms of the GFX License. If a copy of + * the license was not distributed with this file, you can obtain one at: + * + * http://ugfx.org/license.html + */ + +#ifndef _LLD_GINPUT_MOUSE_CONFIG_H +#define _LLD_GINPUT_MOUSE_CONFIG_H + +#define GINPUT_MOUSE_EVENT_TYPE GEVENT_TOUCH +#define GINPUT_MOUSE_NEED_CALIBRATION TRUE +#define GINPUT_MOUSE_LLD_CALIBRATION_LOADSAVE FALSE +#define GINPUT_MOUSE_MAX_CALIBRATION_ERROR 12 +#define GINPUT_MOUSE_READ_CYCLES 4 +#define GINPUT_MOUSE_POLL_PERIOD 25 +#define GINPUT_MOUSE_MAX_CLICK_JITTER 2 +#define GINPUT_MOUSE_MAX_MOVE_JITTER 2 +#define GINPUT_MOUSE_CLICK_TIME 500 + +#endif /* _LLD_GINPUT_MOUSE_CONFIG_H */ + diff --git a/boards/base/Olimex-STM32-LCD/readme.txt b/boards/base/Olimex-STM32-LCD/readme.txt new file mode 100644 index 00000000..539d48e4 --- /dev/null +++ b/boards/base/Olimex-STM32-LCD/readme.txt @@ -0,0 +1,6 @@ +This directory contains the interface for the Olimex-STM32-LCD board +running ChibiOS/RT. + +As this is not a standard ChibiOS/RT supported board, the necessary board files have +also been provided in the chibios_board directory + |