ath79: add support for D-Link DAP-2680 A1

Specifications:
 * QCA9558, 16 MiB Flash, 256 MiB RAM, 802.11n 3T3R
 * QCA9984, 802.11ac Wave 2 3T3R
 * Gigabit LAN Port (AR8035), 802.11at PoE

Installation:
 * Factory Web UI is at 192.168.0.50
   login with 'admin' and blank password, flash factory.bin
 * Recovery Web UI is at 192.168.0.50
   connect network cable, hold reset button during power-on and keep it
   pressed until uploading has started (only required when checksum is ok,
   e.g. for reverting back to oem firmware), flash factory.bin

After flashing factory.bin, additional free space can be reclaimed by
flashing sysupgrade.bin, since the factory image requires some padding
to be accepted for upgrading via OEM Web UI.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>

1 files changed, 89 insertions, 0 deletions

diff --git a/target/linux/ath79/dts/qca9558_dlink_dap-2680-a1.dts b/target/linux/ath79/dts/qca9558_dlink_dap-2680-a1.dts
new file mode 100644
index 0000000000..c3c82937a8
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_dlink_dap-2680-a1.dts
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+#include "qca95xx_dlink_dap-2xxx.dtsi"
+
+/ {
+	compatible = "dlink,dap-2680-a1", "qca,qca9558";
+	model = "D-Link DAP-2680 A1";
+
+	aliases {
+		led-boot = &led_power_green;
+		led-failsafe = &led_power_red;
+		led-running = &led_power_green;
+		led-upgrade = &led_power_red;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power_red: power_red {
+			label = "red:power";
+			gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+		};
+
+		led_power_green: power_green {
+			label = "green:power";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+	};
+};
+
+&partitions {
+	partition@70000 {
+		label = "firmware";
+		reg = <0x70000 0xee0000>;
+		compatible = "wrg";
+	};
+
+	partition@f50000 {
+		label = "dlink";
+		reg = <0xf50000 0xa0000>;
+		read-only;
+	};
+
+	art: partition@ff0000 {
+		label = "art";
+		reg = <0xff0000 0x10000>;
+		read-only;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	pll-data = <0x82000000 0x80000101 0x80001313>;
+
+	phy-handle = <&phy4>;
+	phy-mode = "rgmii-id";
+
+	gmac-config {
+		device = <&gmac>;
+		rgmii-enabled = <1>;
+		rxd-delay = <3>;
+		rxdv-delay = <3>;
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};